load
work
mode
1:manual mode
K 3
K 1
K 2
3
：
K1
K2
K 1
K 2
K 1
K 2
Single period real time control
：
Set load working mode
There are 5 load working modes:
1: manual mode: press the K4 button to turn the load output on or off.
2: pure light control mode: the voltage of the solar panel is detected automatically, the load is turned on at dark and the load is
turned off at dawn.
3: light c time control mode: the load starts the light control, and the load closing time is set by the user.
4: single real time control: Users can set real-time time to enable and close the load.
5: double-time real time control : , users can set two real-time periods to output and turn off the load of the controller, such as
8: 00 a.m. to 10:00 and 2: 00 p.m. to 4: 00 p.m.
Set operation instructions:
Manual mode and pure light control
mode do not need to set the time, and the other three modes need to set the working time.
The operation are as follows:
Light c time control
: Turn the page to the load working mode to light c time control interface (mode 3), press K3 key,
"SET" and "H" font flash, press K1 or K2 key to set the number of hours, the setting is finished.
Then press K3 key, "SET" and "M" font flash, press K1 or K2 key to set the number of minutes, after setting, press K3 key again,
“SET" and "M" stop flashing, save finished
Turn the page of the load working mode to the single real time control interface (mode 4)
1.
Press K3 key, "H" flashing, "ON" on, short press K1 or K2 key to cycle change hours: 0- - 23.
2. Press K3 again, "H" stops flashing, "M" flashes, press K1 or K2 to change the number of minutes: 0--59.
3. Press the K3 key again, when the load time is set, the “ON” icon is off; the “OFF” icon is on, the “M” icon stops flashing, the
“H” icon is flashing, and press K1 or K2 key to modify the cycle number of hours: 0--23.
4. Press the K3 key again, the “H” icon stops flashing, the “M” icon flashes, press K1 or K2 key to change the number of minutes in a
cycle: 0--59.
5. Press the K3 key again, the SET and M icons stop flashing, the load time is set, and save the settings.
Dual-period real-time control mode
Turn the page of the load working mode to the dual-period real time control interface (mode 5)
1.
Press the K3 key, the “H” icon flashes, the “ON1” icon is on, press K1 or K2 key to modify the cycle number of hours: 0--23.
2.
Press the K3 key again, the “H” icon stops flashing, the “M” icon flashes, press K1 or K2 key to change the number of minutes
in a cycle: 0--59.
3. Press the K3 key again, when the load time 1 is set, the” ON1” icon is off, the “OFF1” icon is on, the “M” icon stops flashing,
the” H” icon flashes, and press K1 or K2 key to modify the cycle number of hours: 0--r23.
4. Press the K3 key again, the” H” icon stops flashing, the “M” icon flashes, press K1 or K2 key to change the number of minutes
in a cycle: 0--59.
5. Press the K3 key again, the “M” icon stops flashing, the load time 1 is set up, the “H” icon flashes, the “ON2” icon is om, press
the K1 or K2 key to modify the cycle number of hours: 0--23.
6. Press the K3 key again, the “H” icon stops flashing, the “M” icon flashes, press K1 or K2 key to change the number of minutes
in a cycle: 0--59.
7. Press the K3 key again, when the load time 2 is set, the “ON2” icon is off, the “OFF2” icon ison, the “M” icon stops flashing, the
“H” icon flashes, press K1 or K2 key to modify the cycle number of hours: 0--23.
8. Press the K3 key again, the “H” icon stops flashing, the “M” icon flashes, press K1 or K2 key to change the number of minutes
in a cycle: 0-- 59.
9. Press the K3 key again, the “SET” and” M” icons will stop flashing, and the load time 2 will be set up. Save the settings.
2:pure light mode
Light c
time control
4: Single period
real time control
5: Dual-period
real-time control
mode
ON
OFF
Load OFF
K4
K 4
短按
Load ON
Manually turn on and off the load
When the load mode is manual mode 1 and is not in the "alarm function" period, short press the K4 button to turn on the load,
while in ot her modes, the K4 button is invalid
