background image

STEP 2    (See Diagram 2) 

A.) Attach four Bushings (#27) to a Seat Support Frame (#6).  
B.) Attach a Backrest Support (#7) to the rear of the Seat Support Frame (#6). Align the holes and 

secure them with one M10 x 1 ¾” Allen Bolt (#37) and 

 ¾” Washer (#42).  Repeat the same 

procedure to install the other side. 

C.) Attach two Bushings to the pivot on the Sliding Block (#8). Attach two Bushings to each Backrest 

Supports (#7).  Align the holes and secure them with one M10 x 6 ¾” Allen Bolt (#38), two 

 ¾” 

Washers (#42), and one M10 Aircraft Nut (#44).  Do not over tighten the nut and bolt.  The 
Supports need to swivel on the Bolt. 

D.) Attach two Bushings to the pivot on the Main Frame (#1).  Loosen and pull the Lock Knob on the 

Sliding Block (#8).  The Sliding Block needs to be able to slide on the Chromed Incline Adjustment 
Bar (#9).  Align the two Seat Support Frames (#6) to both ends of the pivot on Main Frame.  Secure 
them with one M10 x 8 ¼” Allen Bolt (#39), two 

 ¾” Washers (#42), and one M10 Aircraft Nut 

(#44).  Use the Lock Knob on the Sliding Block (#8) to adjust and secure the backrest incline 
position.   

 

25 

Содержание MARCY DIAMOND ELITE MD-9010


































Отзывы: