manualshive.com logo in svg

moyno 20302, Руководство по обслуживанию, Страница: 16 / 40

Поделиться
Скачать
moyno 20302 Скачать руководство пользователя страница 16

2.

Install packing (42) before installing shaft assembly
using the following procedure:

a.

Lubricate each individual ring of packing with a
grease that is insoluble in the fluid being pumped.

b.

Individually assemble each ring of packing loosely
in the packing chamber of the pump body (1).
Stagger splits on rings. (Four rings, 3/16 inch
square required on Model 34411; four rings, 1/4
inch square and two lantern ring halves (57)
assembled between two rings on 356 Models).

c.

Loosely install packing gland (41) on pump body (1)
using gland bolts (47).

3.

Press shaft assembly into pump body (1) positioning
slinger ring (77) between packing gland (41) and bear-
ing end of pump body. Secure the shaft assembly with
snap ring (66).

4.

Thread flexible joint (24) into shaft (26) in a clockwise
direction (RH thread).

5.

Thread rotor (22) onto flexible joint (24) in a clockwise
direction (RH thread).

6.

Slide stator (21) on rotor (22). On 331 and 332 Models,
insert rounded end of stator ring (135) into end of stator
prior to installing stator on rotor.

7.

Secure stator (21) and suction housing (2), with suction
port vertically up, to pump body (1) using screws

(112).

8.

Proceed as in installation instructions.

Note: Adjust newly installed packing as described in

maintenance procedure.

WARNING: Replace belt or coupling guards

before reconnecting power.

Page 4

Содержание 20302









































Отзывы:

Нет отзывов