– 4 –
– 5 –
– 6 –
www.moxa.com/support
The Americas: +1-714-528-6777 (toll-free: 1-888-669-2872)
Europe: +49-89-3 70 03 99-0
Asia-Pacific: +886-2-8919-1230
China: +86-21-5258-9955 (toll-free: 800-820-5036)
2009 Moxa Inc. All rights reserved.
* NPort W2250 Plus Series only
NOTE
Do not use the 1 KΩ setting while in RS
-232 mode. Doing
so will degrade the RS-232 signals and reduce the effective
communication distance.
5.
First-time Hardware Installation
STEP 1: After removing the NPort W2150/2250 Plus from the box,
use a cross-over Ethernet cable to connect the NPort’s
RJ45 Ethernet port directly to your computer’s Ethernet
port.
STEP 2: Attach the power adaptor to the NPort and then plug the
adaptor into an electrical outlet.
STEP 3: Configure the NPort W2150/2250 Plus through the
Ethernet port. See the next section for software
installation information.
NOTE
You must connect the Ethernet cable first before powering
up your NPort.
6.
Software Installation Information
Insert the Document & Software CD into your PC. A window should
open with several options displayed:
•
Click
[Install COM Driver]
and follow the on-screen
instructions to install the COM drivers.
•
Click
[Documents]
and select “NPort W2150/2250 Plus
Series User’s Manual” to view the user’s manual.
•
Click
[Install UTILITY]
and follow the on-screen instructions
to install the NPort Search Utility. This utility can be used to
search for NPort W2150/2250 Plus units on the network.
7.
Setting the IP Address
The factory default IP settings are assigned as follows:
LAN:
Static; IP = 192.168.126.254; netmask =
255.255.255.0
WLAN Static; IP
=
192.168.127.254
; netmask =
255.255.255.0
If the NPort is configured for DHCP but the DHCP server cannot be
found, the NPort will use factory default IP settings.
NOTE
If you have forgotten the NPort’s IP address, use the NPort
Search Utility from your PC to locate the NPort. After
searching the LAN for NPort units, the NPort Search Utility
will display the IP address of each unit.
NOTE
Only one network interface can be active at a time. If the
Ethernet link is active, the WLAN will be inactive. If the
WLAN is active, the Ethernet link will be inactive.
Open the web console to make configuration changes as follows:
STEP 1: Open your web browser.
STEP 2: In the address bar, enter 192.168.126.254 (the default
IP address).
STEP 3: The web console will open, and the current configuration
settings will be displayed.
STEP 4: For first time users, click the Wizard in the left navigation
panel. The wizard will prompt you to configure the IP
address, SSID, and security mode. For other settings,
use the factory defaults or modify the settings for your
application.
8.
Pin Assignments and Cable Wiring
Pin
RS-232
RS-422,
4w RS-485
2w RS-485
1
DCD
TxD-(A)
---
2
RXD
TxD+(B)
---
3
TXD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5
GND
GND
GND
6
DSR
---
---
7
RTS
---
---
8
CTS
---
---
9
---
---
---
DB9-to-DB25 cables are available as optional accessories for
connecting the NPort W2150/2250 Plus to RS-232 serial devices.
The cable wiring diagrams are shown below. Female-to-female
versions are also available.
Female DB9 to Male DB9
Female DB9 to Male DB25
9.
Specifications
Power Requirements
Power Input
12 to 48 VDC
Power Consumption
560 mA
Power Connector
Power jack and terminal block
Physical Characteristics
Material
Aluminum sheet metal (1 mm)
Dimensions
77 × 111 × 26 mm (no ears, no antenna)
100 × 111 × 26 mm
(with ears, no antenna)
Antenna Length
109 mm
Magnetic Isolation
1.5 KV magnetic isolation built-in
Environmental Limits
Operating Temperature Standard Models:
0 to 55°C (32 to 131°F), 5 to 95%RH
Wide Temp. Models:
-40 to 75°C (-40 to 167°F), 5 to 95%RH
Storage Temperature
-20 to 85°C (-4 to 185°F), 5 to 95%RH
Regulatory Approvals
EMC
CE: EN55022 Class A/EN55024
ETSI EN 301 489-17,
ETSI EN 301 489-1
FCC: FCC Part 17 Subpart B, Class A
FCC Part 15 Subpart B, Class A
EMS
IEC 61000-4-2 (ESD) Level 3
Safety
UL: UL60950-1
TÜV: EN60950-1
DSPR: ARIB-STD 33, ARIB-STD 66
