Moxa Technologies NPort-IA-5250 Скачать руководство пользователя страница 7

Страница: 7 / 119

NPort IA5150/5250 Series User’s Manual

Introduction

1-3

Product Features

NPort IA5150/5250 Series device servers have the following features:

Make your serial devices Internet ready

Versatile socket operating modes, including TCP Server, TCP Client, UDP, and Real COM

driver

2- or 4-wire RS-485 with patented ADDC™ (Automatic Data Direction Control)

Slim type, inch-wide industrial strength casing

DIN-Rail or wall mountable

Built-in Ethernet cascading ports for easy wiring (RJ45 only)

Redundant dual DC power inputs

Warning by relay output and E-mail

10/100BaseTX (RJ45) or 100BaseFX (SC connector, Single/Multi mode) available

IP30

Product Specifications

NPort IA5150-M-SC/5150I-M-SC/5150-S-SC/5150I-S-SC LAN

Ethernet Port

1 100BaseFX port (SC connector)

NPort IA5150/5150I/5250 LAN

Ethernet Switch Ports

2 10/100BaseT(X) ports (RJ45 connector)

Protection

Built-in 1.5 KV magnetic isolation

Optical Fiber

Distance

Multi mode: 0 to 2 km, 1310 nm (62.5/125

m, 500 MHz*km)

Single mode: 0 to 40 km, 1310 nm (9/125

m, 3.5 PS/(nm*km)

Min. TX Output

Multi mode: -20 dBm
Single mode: 0 to 40 km, -5 dBm

Max. TX Output

Multi mode: -14 dBm
Single mode: 0 to 40 km, 0 dBm

Sensitivity

-36 to -32 dBm (Single), -34 to -30 dBm (Multi)

NPort IA5150 Series Serial Interface

Interface RS-232/422/485

No. of Ports

Port Type

Male DB9 for RS-232;
5-pin terminal block for RS-422/485

Signals

RS-232

TxD, RxD, RTS, CTS, GND, DTR, DSR,
DCD

RS-422:

Tx+, Tx-, Rx+, Rx-, GND

RS-485 (2-wire):

Data+, Data-, GND

RS-485 (4-wire):

Tx+, Tx-, Rx+, Rx-, GND

Serial Line Protection

15 KV ESD for all signals

Содержание NPort-IA-5250























































































































Результаты поиска

Содержание NPort-IA-5250

Отзывы:

Похожие инструкции для NPort-IA-5250

Бренды по названию

Популярные бренды

Moxa Technologies NPort-IA-5250, Руководство пользователя

Результаты поиска

Содержание NPort-IA-5250

Отзывы:

Похожие инструкции для NPort-IA-5250

Бренды по названию

Популярные бренды