Moxa Technologies NPort-IA-5250 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 119

background image

1

1

Chapter 1

Introduction

Welcome to the NPort IA Series of industrial serial device servers. In this manual, we refer to the
seven products in the series collectively as “NPort IA5150/5250 Series.”

The sixteen models in the NPort IA5150/5250 Series are:

1. NPort IA5150

1-port RS-232 (DB9), RS-422/485 (TB) to Ethernet Device Server

2. NPort IA5150I

1-port RS-232 (DB9), RS-422/485 (TB) to Ethernet Device Server,
w/ 2KV Isolation protection

3.NPort IA5150-M-SC

1-port RS-232 (DB9), RS-422/485 (TB) to Multi-mode Fiber
Device Server

4.NPort IA5150I-M-SC

1-port RS-232 (DB9), RS-422/485 (TB) to Multi-mode Fiber
Device Server w/ 2KV Isolation protection

5. NPort IA5150-S-SC

1-port RS-232 (DB9), RS-422/485 (TB) to Single-mode Fiber
Device Server

6. NPort IA5150I-S-SC

1-port RS-232 (DB9), RS-422/485 (TB) to Single-mode Fiber
Device Server w/ 2KV Isolation protection

7. NPort IA5250

2-port RS-232/422/485 (DB9) to Ethernet Device Server

8.NPort IA5150-T

1-port RS-232 (DB9), RS-422/485 (TB) to Ethernet Device Server,
wide temperature(-40 to 75

◦

C)

9. NPort IA5150I-T

1-port RS-232 (DB9), RS-422/485 (TB) to Ethernet Device Server,
w/ 2KV Isolation protection, wide temperature(-40 to 75

◦

C)

10. NPort IA5150-M-SC-T

1-port RS-232 (DB9), RS-422/485 (TB) to Multi-mode Fiber
Device Server, wide temperature(-40 to 75

◦

C)

11. NPort IA5150I-M-SC-T

1-port RS-232 (DB9), RS-422/485 (TB) to Multi-mode Fiber, wide
temperature(-40 to 75

◦

C) Device Server w/ 2KV Isolation

protection

12. NPort IA5150-S-SC-T

1-port RS-232 (DB9), RS-422/485 (TB) to Single-mode Fiber
Device Server, wide temperature(-40 to 75

◦

C)

13. NPort IA5150I-S-SC-T

1-port RS-232 (DB9), RS-422/485 (TB) to Single-mode Fiber
Device Server w/ 2KV Isolation protection, wide temperature(-40
to 75

◦

C)

14. NPort IA5250-T

2-port RS-232/422/485 (DB9) to Ethernet Device Server, wide
temperature(-40 to 75

◦

C)

The following topics are covered in this chapter:

Package Checklist

Product Features

Product Specifications

«
...
3
4
5
6
7
...
»

Содержание NPort-IA-5250
























































































































Отзывы:

Нет отзывов

Похожие инструкции для NPort-IA-5250

Бренд: Fagor Страницы: 12

Бренд: Sungrow Страницы: 14

Бренд: Senergy Страницы: 50

Бренд: Nitek Страницы: 2

Бренд: OTS Страницы: 3

Бренд: Microchip Technology Страницы: 56

Бренд: Nuova Marea Страницы: 9

Бренд: Tyba Страницы: 14

Бренд: Energie Страницы: 36

Бренд: Green Cell Страницы: 44

Бренд: Kings Audio Страницы: 6

Бренд: SMA Страницы: 90

IGSI - 3 Series

Бренд: InfluxGreen Страницы: 37

Бренд: AVT Страницы: 70

VS-700L ViewStream 700L

Бренд: DV Signage Страницы: 30

Бренд: Arec Страницы: 46

Бренд: RGBlink Страницы: 9

FABRICATOR 181i

Бренд: Thermal Arc Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды