– 1 –
– 2 –
– 3 –
P/N: 1802066500013
NPort 6600 Series
Quick Installation Guide
F
if
th Edition,
March
2011
1.
Overview
The NPort 6600 series of serial device servers includes 8-port,
16-port, and 32-port models for connecting larger numbers of
serial devices to Ethernet. Some applications now also require
better security when transmitting data through a network. The
NPort 6600 series of device servers use DES, 3DES, and AES data
encryption to provide secure network communication.
2.
Package Checklist
Before Installing your NPort 6600 series secure device server,
verify that the package contains the following items:
•
1 NPort 6600 device server
•
CBL-RJ45M9-150: 8-pin RJ45 to DB9 male connection cable,
150 cm
•
Power Cord (AC models only)
•
2 rack-mount ears
•
Documentation and software CD
•
Quick installation guide (printed)
•
Warranty card
Optional Accessories
•
DK-35A: 35 mm DIN-Rail Mounting Kit
•
DIN-Rail Power Supply
•
NM-TX01/NM-TX01-T: Network module with one
10/100BaseTX Ethernet port (RJ45 connector; supports
cascade redundancy)
•
NM-FX01-S-SC/NM-FX01-S-SC-T: Network module with one
100BaseFX single mode fiber port (SC connector; supports
cascade redundancy)
•
NM-FX02-S-SC/NM-FX02-S-SC-T: Network module with two
100BaseFX single mode fiber ports (SC connectors; supports
cascade redundancy)
•
NM-FX01-M-SC/NM-FX01-M-SC-T: Network module with one
100BaseFX multi mode fiber port (SC connector; supports
cascade redundancy)
•
NM-FX02-M-SC/NM-FX02-M-SC-T: Network module with two
100BaseFX multi mode fiber ports (SC connectors; supports
cascade redundancy)
•
NM-GPRS/GSM: GPRS/GSM modem module
•
NM-Modem/NM-Modem-T: One PSTN modem port with RJ11
connector
NOTE: Please notify your sales representative if any of the above
items is missing or damaged.
3.
Hardware Introduction
Demonstrated 8 port model to be an example.
Reset button
Press the Reset button continuously for 5 sec to load factory
defaults
Adjustable pull high/low resistor for RS-485 (150 K
Ω
or 1
K
Ω
)
The NPort 6650 has 3 DIP Switches associated with each serial port
for configuring the pull high/low resistors for RS-485 applications.
The switches are located in a recess on the bottom of the NPort
6650. To access the switches, first remove the panel covering the
recess.
: Use a pointed object to press the reset button. Release
the button after the Ready LED stops blinking.
SW 1
2
3
Pull High Pull Low Terminator
ON 1 K
Ω
1 K
Ω
120 K
Ω
OFF 150 K
Ω
150 K
Ω
---
NOTE:
For RS-232 applications, all DIP Switches for the port
should be set to the OFF position.
Rack Mounting
Use four screws to attach the NPort 6610/6650 to a standard rack
LED Indicators
Name
Color
Function
PWR
Red
Power is being supplied to the power input.
Ready
Red
Steady
on:
Power is on and the NPort 6600
series is booting up.
Blinking: IP conflict, DHCP or BOOTP server
not responding, or relay output.
Check relay output first. If still
blinking, then there is an IP
conflict, or the DHCP or BOOTP
server did not respond properly.
Green
Steady
on:
Power is on and the NPort 6600
series is functioning normally.
Blinking: The device server has been
located by the Administrator’s
Locator function.
Off
Power is off, or power error condition exists.
Link
Orange 10 Mbps Ethernet connection.
Green
100 Mbps Ethernet connection.
Off
Ethernet cable is disconnected, or has a
short.
P1-P16 Tx Green
Serial port is transmitting data.
Off
No data is being transmitted through the
serial port
P1-P16 Rx Orange Serial port is receiving data..
Off
No data is being received through the serial
port.
FX
Orange Steady on:
Ethernet fiber connection,
but port is idle.
Blinking:
Fiber port is transmitting or
receiving data.
P1-P16
in-use
LEDs
Green
Serial port is opened by server side
software.
Off
Serial port is not opened by server side
software.
Alarm
Red
The relay Dout is open (exception)
Off
The relay Dout is Shorted (normal)
Module
Green
Network module is plugged in and detected
Off
No module present
GSM
Green
GSM Connection
GPRS
Orange GPRS Connection
GPRS/GSM
Signal
Strength
Green
More LEDs indicates better signal; 4 LEDs
indicates maximum signal strength.
