background image

A.

 

Regulatory Approval Statement 

 

 

This device complies with part 15 of the FCC Rules. Operation is subject to the following 
two conditions: (1) This device may not cause harmful interference, and (2) this device 
must accept any interference received, including interference that may cause undesired 
operation. 

Class A

  FCC Warning! This equipment has been tested and found to comply with the limits for a Class A digital 

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference when the equipment is operated in a commercial environment. This equipment 
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the 
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in 
a residential area is likely to cause harmful interference in which case the user will be required to correct the 
interference at his own expense. 

 

 

European Community 

Warning: 
This is a class A product. In a domestic environment this product may cause radio interference in which case 
the user may be required to take adequate measures. 

 

Содержание MC-7130-MP












































Отзывы: