Moxa Technologies EtherDevice EDS-518A Series Скачать руководство пользователя

Страница: 70 / 97

EDS-518A Series User’s Manual

Featured Functions

3-55

Email Setup

Mail Server IP/Name

Setting

Description

Factory Default

IP address

The IP Address of your email server.

None

Account Name

Setting

Description

Factory Default

Max. 45
Characters

Your email account name (typically your user name)

None

Password Setting

Setting

Description

Factory Default

Disable/Enable to
change Password

To reset the Password from the Web Browser interface,
click the Change password check-box, type the Old
Password, type the New Password, retype the New
password, and then click Activate; Max. 45 Characters.

Disable

Old Password

Type the current password when changing the password

None

New Password

Type new password when enabled to change password;
Max. 45 Characters.

None

Retype Password If you type a new password in the Password field, you

will be required to retype the password in the Retype
new password field before updating the new password.

None

Email Address

Setting

Description

Factory Default

Max. 30
characters

You can set up to 4 email addresses to receive alarm
emails from EDS-518A.

None

Send Test Email

After configuring the email settings, you should first click

Activate

to activate those settings, and

then click

Send Test Email

to verify that the settings are correct.

Содержание EtherDevice EDS-518A Series


































































































Результаты поиска

Содержание EtherDevice EDS-518A Series

Отзывы:

Похожие инструкции для EtherDevice EDS-518A Series

Бренды по названию

Популярные бренды

Moxa Technologies EtherDevice EDS-518A Series, Руководство пользователя

Результаты поиска

Содержание EtherDevice EDS-518A Series

Отзывы:

Похожие инструкции для EtherDevice EDS-518A Series

Бренды по названию

Популярные бренды