Mouser IB970 Скачать руководство пользователя страница 44

Страница: 44 / 79

BIOS SETUP

IB970 User’s Manual

USB Configuration

Main Advanced

Chipset

Boot

Security

Save & Exit

USB Configuration

→ ←

Select Screen

↑↓

Select Item

Enter: Select
+- Change Field
F1: General Help

F2: Previous Values
F3: Optimized Default

F4: Save ESC: Exit

XHCI Pre-Boot Driver

Disabled

xHCI Mode

Auto

HS Port #1 Switchable

Enabled

HS Port #2 Switchable

Enabled

HS Port #3 Switchable

Enabled

HS Port #4 Switchable

Enabled

xHCI Streams

Enabled

EHCI1

Enabled

EHCI2

Enabled

USB Ports Per-Port Disable Control

Disabled

HS Port #1/2/3/4 Switchable

Allows for HS port switching between xHCI and EHCI. If disabled, port
is routed to EHCI. If HS port is routed to xHCI, the corresponding SS
port is enabled.

xHCI Streams

Enable or disable xHCI Maximum Primary Stream Array Size.

EHCI1/2

Control the USAB EHCI (USB 2.0) functions. One EHCI controller must
always be enabled.

USB Ports Per-Port Disable Control

Control each of the USB ports (0~13) disabling.

Содержание IB970
















































































Результаты поиска

Содержание IB970

Отзывы:

Mouser IB970, Руководство пользователя, Страница: 44 / 79

Результаты поиска

Содержание IB970

Отзывы: