Mountz PULSE TOOLS Скачать руководство пользователя страница 40

Страница: 40 / 50

Mountz Inc. 1080N 11

Street, San Jose CA 95112 Ph (408) 292-2214 Fax (408) 292-2733

www.mountztorque.com

6.4

If the test result is NG (see Chart 16 in reference to the torque standard), MUST draw out or add a

little mount of oil and do the following steps:

6.4.1

Loosen the pulse unit housing by hands.

6.4.2

Loosen the greasing screw.

6.4.3

Draw out or add a little amount of oil.

6.4.4

Tighten

the

greasing

screw

back.

6.4.5

Tighten the pulse unit housing.

6.4.6

Test the torque again. If the test result is still NG, repeat the Steps 6.4.1 to 6.4.5 until

the

proper

torque

reached.

7.0 Pulse Unit Housing Assembly

Fix the housing by a vise. Turn the wrench in counter clockwise direction to tighten the pulse unit

housing.

Model No.

Air inlet pressure 85 PSI

N.M (at least)

FLEXS-40P 15.5

FLEXS-50P 25

FLEXS-60P 35

FLEXS-70P 55

FLEXS-90P 90

FLEXS-100P 125

FLEXS-130P 145

FLEXS-150P 210

FLEXS-30PX 12.5

FLEXS-40PX 14

FLEXS-50PX 22

FLEXS-60PX 28

Chart 16

Note: Handle rubber must
be covered by a piece of
cloth to avoid damage

Fig.114

Содержание PULSE TOOLS



















































Результаты поиска

Содержание PULSE TOOLS

Отзывы:

Бренды по названию

Популярные бренды

Mountz PULSE TOOLS, Инструкция по эксплуатации

Результаты поиска

Содержание PULSE TOOLS

Отзывы:

Бренды по названию

Популярные бренды