B
Lift and hang TV assembly onto arm and wall
plate.
Secure the monitor plate to the arm
and wall plate with the removed
screws and washers from the
previous step.
Tilting angle adjustment (+3° / -10°)
Leveling adjustment
Loosen the screws
Tighten the screws
Tilt the TV
Loosen the screw
Tighten the screw
Level the TV
Adjust TV to your desired angle then fasten tilting screws with open-end wrench.
If needed, TV can be leveled via adjusting the screw with the open-end wrench or
screwdriver.
Adjustments
B
B
B
B
B
Switch screen horizontally and vertically
If needed, the TV can be rotated ±90 degrees for switching screen between horizontally and vertically
.
Use the open-end wrench to
loosen and tighten this screw if
necessary.
Screwdriver can be used for
adjusting the screw to secure the
TV direction if need.
No need to adjust this screw if
the mount can hold the TV at your
desired direction via the default
factory setting.
Horizontal screen
±90°
0° up
Product dimensions:
5-1
5-2
5-3
Tighten
B
+3 /-10°
Vertical screen
90° up
163mm
/6.4"
60mm/2.4"
145mm
/5.7"
Φ
7mm/3"
200mm/7.9"
150mm/5.9"
200mm
/7.9"
150mm
/5.9"
100mm
/3.9"
75mm
/3"
100mm/3.9"
75mm/3"
219mm/8.6"
219mm
/8.6"
Φ
8.5mm/0.3"
Φ
6.7mm/0.3"
25mm/1"
30mm/1.2"
Φ
16.1mm/0.6"
62mm/2.4"
319.5mm/12.6"
134.5mm/5.3"
55.5mm/2.2"
170mm/6.7"
375mm/14.7"
69mm/2.7"
210mm/8.3"
15mm/0.6"
+3°
-10°
A
Step 5 Lift and hang TV with brackets onto wall bracket
Contact us to have these additional pieces
shipped directly to you
Concrete wall anchor 2pcs (NOT INCLUDED)
Ø10*61mm
01
A
A
A
01
01
Install wall plate using lag bolts
and anchors (not included)
with Socket
Wrench, NO Electrodrill.
Tighten the
lag bolts until they are pulled firmly
against the wall plate . Tighten the
lag bolts until they are pulled firmly
against the wall plate
.
01
Remove 2 preassembled screws and washers
before hang TV on to the wall bracket, and
save them for using to next step.
UP
2
4B-3
No!
Step 4A Wall plate installation (wood stud)
4A-1
4A-2
Locate your studs. Verify and
mark the center of the stud by
finding the stud edges using an
awl, a thin nail, or an
edge-to-edge stud finder.
Position the wall plate at your desired height
and line up the holes with your stud center line.
Level the wall plate and mark the pilot hole
locations x2.
01
4A-3
Drill pilot holes using a 5/32 in. (4 mm) diameter drill bit.
IMPORTANT
:
Pilot holes must be drilled to a depth
of 2 3/4 in (70 mm). Be sure to drill into the center of the stud.
5/32 in Ø4 mm
4A-4
01
A
A
Install wall plate using lag bolts
with Socket Wrench, NO Electrodrill.
Tighten the lag bolts until they are
pulled firmly against the wall plate
.
01
01
Position the wall plate at
your desired height , level
the wall plate and mark the
pilot hole locations x2.
4B-1
Step 4B Wall plate installation (concrete or brick)
01
Level
01
A
4B-2
Drill pilot holes
2.75in
(
70 mm
）
Ø 10 mm
Ø 10 mm
3/8in
UP
2
No!
2.75in (70 mm)
01
Level
UP
UP
B
Remove 2 preassembled
screws and washers
before hang TV on to the
wall bracket, and save
them for using to next
step.
Loosen
7
6
8
11
10
9