Eyelet
Mounting
Strap
M100 GameSpy Digital Camera
PlotStalker Software
Page 3
Page 14
Capture Mode
TRAIL CAM (Still)
Photo Quality
HIGH
Photo Delay
after each photo is taken
1 MIN
Multi Shot Count
1-SHOT
Digital Zoom
NO ZOOM
Video Resolution
HIGH
Video Length
5 SEC
Video Audio
ON
Camera Name
MYCAMERA
Temperature
Fahrenheit
Info Strip
printed on photos
ON
Plot Frequency
15 SECONDS
Plot Duration
3 HOUR
Default Setting
NO
Delete All?
NO
PLOTSTALKER ACTIVITY SEARCH
B
ACTIVITY SEARCH
The Search Feature will scan through your photos and automatically
look for changes in regions that you identify in Setup.
In search mode, the PlotStalker software scans through the .mlt photo file, stops on
a photo when changes are found in your identified region, and then highlights the
changes in blue. You can click anywhere in the video viewing area to remove the
blue highlights.
ACTIVITY SEARCH SETUP
Click the Settings button to activate
the Region and Sensitivity settings
for the Activity Search
1
2
3
Click on the Set Motion Search Area Button.
Use the mouse to select and drag the red outline around the area you want to
search for movement. This allows you to focus on a very precise area if
required.
Click OK button on the Settings Popup window to confirm your settings and
exit the menu.
Set to High, Medium or Low - This sets the level of pixel change the program
will detect. Note; a pixel change will occur with a color, intensity, lighting or
movement so this setting is critical to obtain the desired results.
1
SENSITIVITY
Click on Default button to return to the default values for Search Area and
Sensitivity settings
1
DEFAULT SETTINGS
DEFINE SEARCH REGION
Provides the ability to search for
changes in the photo in a specific
region rather than the entire photo.
Slide the UNLOCK switch on the bottom of Camera and use the knob to pull
the slide-out Battery Tray. Install four(4) or eight(8) AA size alkaline or
lithium batteries with polarities as indicated in the Battery Tray. Re-install
the Battery Tray.
Thread the provided Mounting Strap through the Eyelets on the back of the
camera and secure to a tree or pole approximately 36" from the ground as
shown.
Turn Camera on by sliding ON/OFF/AIM switch to
the ON position.
Press the MODE button one time to get to the
Camera Setup Menu. Set Time and Date by pressing
ENTER, using UP/DOWN to adjust selected field,
LEFT/RIGHT to move to the next field and ENTER
when done.
Press MODE button until MENU SELECTION
screen is displayed. Use the UP/DOWN buttons
until the MAIN SCREEN option is highlighted
yellow. Press ENTER.
Your Camera will now automatically take pictures
whenever an animal is detected in range -based on
the default settings below.
TRAIL CAM MODE
Still photos are taken when an animal is detected. The number of photos taken
when an animal is detected is configurable in Settings. Photos are stored in
the in the DCIM/100_MDGC folder on the SD card.
PLOT CAM MODE
The camera takes photos at a specified interval during the day and combines
them together to create a Plot Video (*.MLT file) which can be viewed on the
supplied Moultrie Plot Stalker software. The camera takes a Plot Video twice
a day; once in the morning and once in the evening. The morning Plot Video
begins 30 min before sunrise. The evening Plot Video ends 30 min after
sunset. See chart below as a reference. The length of each Plot Video is
determined by the Plot Duration setting in the camera menu. The camera will
detect the correct sunrise and sunset times automatically and adjust itself
accordingly. The Plot Videos are stored in :/PLOT folder on the SD card.
IMPORTANT: It will take the camera 24hrs to properly adjust to the correct
sunrise and sunset times. As a default the camera will start the morning Plot
Video at 5:30am and end the evening video at 6:30pm. To reset the sunrise
and sunset times back to the default times, use the Default Settings option in
the menu.
The GameSpy offers four capture modes as described below. The default capture
mode is Trail Cam.
HYBRID CAM MODE
Camera operates in Plot Cam mode during the day and Trail Cam Mode during
the night. Thirty minutes after dusk the camera will enter the Trail Cam mode
and take night photos when the PIR sensor is triggered.
VIDEO MODE
Camera records a video when an animal is detected by the motion sensor.
During daylight hours the camera will record a video 5, 15 or 30 seconds in
length. During night the camera will record a video with a maximum length
of 10 seconds. The video length is configurable in SETTINGS.
{
{
Morning Plot Video
Evening Plot Video
4
CAPTURE MODES
PlotStalker Software
M100 GameSpy Digital Camera
Page 13
Page 4
PLOTSTALKER SOFTWARE INTRO
A
INTRODUCTION
In time-lapse photography a series
of still photos are taken at regular
time intervals. The PlotStalker
Software allows you to load the
time lapse file that was captured
from your Moultrie Game Camera
and scroll backward and forward
through your photos, single step,
search for activity in a designated
area, and save the files.
Computer: Intel® Pentium® 4 or AMD Athlon® 64 processor or above; 1GB
RAM minimum; 100 MB hard disk space minimum.
Operating System: Microsoft® Windows® 32 bit - XP with Service Pack 2 or
later; Windows Vista® Home Premium, Business, Ultimate, or Enterprise with
Service Pack 1; or Windows 7
Using standard Microsoft utilities (ex. File Explorer – My Computer),
copy the PlotFiles (extension is .MLT) from the PLOT directory on the
SD card to the hard disk drive in your computer. Note the location stored
on the hard disk drive.
Open the PlotStalker software application from the Windows Start Button
menu. Once in the PlotStalker software, click on the File Button
Browse to the location in which you have saved the Plot file(s)
(.MLT) in step 1 above, select the file of interest and click Open.
1
2
3
LOADING PLOT FILES
Insert the PlotStalker CD into your computer and follow on-screen instructions.
>
SYSTEM REQUIREMENTS
>
SOFTWARE INSTALLATION
BEGIN/END
Goes to the first or last photo in the Plot File.
FRAME BY FRAME SEARCH
Individually step forward or backward through each photo.
REWIND/PAUSE/PLAY
Play photos in sequence, pause, or play the photos in reverse order.
These functions simulate a video and are useful for manually searching
changes in the photos. When a sequence is being played, press
fast-forward or fast-rewind multiple times to increase speed. (1x-5x)
>
