background image

NOTE: This equipment has been tested and found to comply with the limits for a 

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are 
designed to provide reasonable protection against harmful interference in a 
residential installation. This equipment generates uses and can radiate radio 
frequency energy and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television reception, which 
can be determined by turning the equipment off and on, the user is encouraged to 
try to correct the interference by one or more of the following measures: 

 

- Reorient or relocate the receiving antenna. 
- Increase the separation between the equipment and receiver. 
-Connect the equipment into an outlet on a circuit different from that to which the 
receiver is connected. 
-Consult the dealer or an experienced radio/TV technician for help 

 
 

Changes  or  modifications  not  expressly  approved  by  the  party  responsible  for 
compliance could 
  void the user's authority to operate the equipment. 
 
This  device  complies  with  Part  15  of  the  FCC  Rules.  Operation  is  subject  to  the 
following two conditions: 
(1) this device may not cause harmful interference, and   
(2) this device must accept any interference received, including interference that may 
cause   
undesired operation. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Содержание MBRT1










Отзывы: