03
.
CONFIGURATION
▷ TRANSMITTERS CONFIGURATION
▷ FEATURES
FEATURES ◁
INSTALLATION PROCESS ◁
03
.
CONFIGURATION
03.A
03.B
▷ New transmitters configuration - 2 keys (DIP 2 ON)
1 ▷
Press the
P1
button once and the
LED CODE
will light during 6sec.
2 ▷
While the
CODE LED
is light up, press the opening desired transmiter key during
1sec and
CODE LED
will blink twice.
3 ▷
The
CODE LED
will be light up again and you must now press the transmitter key
for closing during 1 sec and
CODE LED
will blink twice.
4 ▷
Let the
CODE LED
go off and the transmitter is now configured.
▷ New transmitters configuration - 1 key (DIP 2 OFF)
1 ▷
Press the
P1
button once and the
LED CODE
will light up during 6sec.
2 ▷
While the
CODE LED
is light up, press the desired transmiter key during 1sec and
CODE LED
will blink twice.
3 ▷
Let the
CODE LED
go off and the transmitter is now configured.
NOTE:
After you program the first transmitter, the control board will only accept new
transmitters of the same type. For example, if the first programmed transmitter is set
for rolling code, the central will only accept more rolling code transmitters until a
maximum of 46 transmitters.
▷ Programming remote controls without access to the control
board
• Using an already configured TRANSMITTER:
1 ▷
Press transmitter’s 1 and 2 keys simultaneously for 3sec.
2 ▷
Press the new transmitter’s desired opening key for 1sec.
3 ▷
Wait 3sec and press the desired closure key for 1sec.
4 ▷
Wait 6sec and can now use the new device.
• Using one PUSH-BUTTON connected to the control board:
1 ▷
Press for 2 seconds simultaneously the opening and closing buttons.
2 ▷
Press the new transmitter’s desired opening key for 1sec.
3 ▷
Wait 3sec and press the desired closure key for 1sec.
4 ▷
Wait 6sec and can now use the new device.
▷ Erase all configured transmitters
1 ▷
Press and hold the
P1 key
for 10sec. The
CODE LED
will remain light up the entire
time and will start to blink at the end of 10sec.
2 ▷
Release the
P1 key
and
LED CODE
will stop flashing and remain lit for 3sec so that
you configure a new transmitter (note the DIP2 position).
3 ▷
If you do not want to configure new transmitter, let the
CODE LED
go off without
pressing any key.
▷ Adjusting the Working Time and the Pause Time
The
Working Time
can be set to 60sec ,90sec and 120sec .
To set any of these values, press the
P2
button as many times as needed until the
desired option is defined
while the engine is running
.
▷ For each pulse in the
P2
button with the motor running, the
CODE LED
will flash
once for 60sec, twice for 90sec and thrice to 120sec.
The
Pause Time
can be set to 30sec, 60sec and 90sec.
To set any of these values, press the
P2
button repeatedly until the desired option is
defined
while the engine is paused
(must enable auto-locking by putting DIP1-ON)
.
▷ For each pulse in the
P2
button with the motor opened in pause time, the
CODE LED
will flash one time for 30sec, two times for 60sec and three times to 90sec.
NOTE:
▷ The
Working Time
should be set to a value above the actual required working time.
For example, if the automatism needs 40sec to go all the course, you must set the
Working Time
for 60sec.
▷ Setting the motor working direction
To verify that the operating direction is correct, proceed as follows:
1 ▷
With a configured transmitter give order with the key that you have programmed in
the first place and the automatism must begin to open. If it starts to close, swap the
motor wires at terminals 4 and 5 from the CN1 connector.
▷ Safety photocells (NC)
1 ▷
To enable the use of photocells, place the Dipper 4 to
OFF
.
Safety photocells act as follows:
▷ In opening maneuvers, has no action.
▷ When opened, the photocells cause the gate to remain open if there is an obstacle in
front of them.
▷ In closing maneuvers, the gate stops and starts to open immediately, stopping at the
end of the working time or at the end of the opening limit-switch.
1 ▷
Connect the control board to a 230V power supply (terminals 1 and 2 - CN1).
2 ▷
Configure the Dippers according to the used devices and the desired type of
operation.
3 ▷
Configure transmitter.
NOTE:
Be aware of any component connected to the control board as the motor or
photocells.
This control board can operate all types of motor which doesn’t exceed 1500W of
power and photocells which doesn’t exceed a consumption over 80mA.
