background image

v.1

11

DataStorm D3 Configuration Pages Cont. 

| Standard Functions

| DataStorm D3 Configuration Page: 

Main 2

 |

17-Azimuth Search Window

  Width in degrees of the actual search 
  pattern window the DataStorm will search
  in for the satellite. [left and right on a 
  horizontal plane]

18-Elevation Search Window

  Height in degrees of the actual search
  pattern window the DataStorm will search
  in for the satellite. [up and down on a
  horizontal plane]

19

-

Motion Stow

  If signal quality is lost for 30 seconds or more,
  the dish will automatically stow if enabled.

20-Manual Location [GPS]

  If enabled the manual GPS coordinates can be
  placed here overriding the automatic 
  functioning of the DataStorm GPS module.

22-Azimuth Origin

  The start mark in degrees for azimuth rotation.

DataStorm D3   

User Guide

14

-

Signal Quality Threshold

  Sets the minimum signal quality needed to 
  peak on a satellite. 

15

-

Signal Strength Threshold

  Sets the minimum signal strength needed to 
  peak on a satellite. Set Signal Strength Threshold 
  to a value as low as possible that does not 
  constantly start and stop azimuth movement. To set
  this value, run a test dish and take note of the
  lowest signal strength reading seen and set your
  threshold for 30 points above that reading.
  This value is 440 - 480 Typical.

16

-

Isolation Optimization

  

Has 3 settings:

 

-

Partial [default]

 

  Indicates that the D3 will perform a cross-pol

 

-

Full

 

  Indicates that the D3 will not only perform a

 

  cross-pol but ensure it’s optimization.

 

-

None [test purposes only]

 

  Indicates the D3 will not perform a cross-pol

 

  and just connect. 

14

15

16

17
18

19

20

21
22

23

24

25

26

Update Settings

   To have the D3 accept any 
   changes  you must click the 
   ‘Update Settings’ button to 
   store the new configuration.

Содержание DataStorm D3






















Отзывы: