Motortech VariFuel3 140-80 Series Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 44

Motortech VariFuel3 140-80 Series Скачать руководство пользователя страница 34

7 Errors

34

Rev. 09/2022

Problem

Possible cause

Solution

Traverse range of the
fuel ring is too small/
too big.

A wrong VariFuel3 is con-
figured in the stepper motor
driver.

Configure your VariStep3 stepper
motor driver via the MICT. After-
wards, if necessary, adjust the fuel
ring (see

Adjust Fuel Ring

on

Fuel ring scale is not in
the inspection window.

Home position lost.

See

Adjust Fuel Ring

on page 39

POWER-LED of the step-
per motor driver does
not light up although it
is connected to the sup-
ply voltage.

Stepper motor driver is
defective.

Replace the stepper motor driver.

Stepper motor does not
move without interrup-
tions.

There is

no

malfunction. When the air/fuel ratio is correct, the

motor remains in its position.

7.3

Fix Shaft

All graphics used in this section represent an example of a VariFuel3 series 200-120.

To fix the shaft between stepper motor and VariFuel3, the stepper motor must be completely
dismounted. The explosion view provides information on how the stepper motor has been in-
stalled.

«
...
32
33
34
35
36
...
»

Содержание VariFuel3 140-80 Series













































Отзывы:

Нет отзывов