Motorola Symbol DS3407 Скачать руководство пользователя страница 41

Страница: 41 / 404

Maintenance and Technical Specifications

3 - 3

Digital scanner decodes bar code,
but does not transmit the data to the
host.

Digital scanner is not programmed
for the correct host type.

Scan the appropriate host type
programming bar code. See the
chapter corresponding to the host type.

Interface cable is loose.

Re-connect the cable.

If 4 long low beeps are heard, a
transmission error occurred.

Set the digital scanner's
communication parameters to match
the host's setting.

If 5 low beeps are heard, a
conversion or format error
occurred.

Configure the digital scanner's
conversion parameters properly.

If low/high/low beeps are heard,
an invalid ADF rule is detected.

Program the correct ADF rules.

If high/low beeps are heard, the
digital scanner is buffering Code
39 data.

Normal scanning a Code 39 bar code
and the Code 39 Buffering option is
enabled.

Host displays scanned data
incorrectly.

Digital scanner is not programmed
to work with the host.

Scan the appropriate host type
programming bar code.

For RS-232, set the digital scanner's
communication parameters to match
the host's settings.

Program the proper editing options
(e.g., UPC-E to UPC-A Conversion).

Digital scanner emits
high/high/high/Low beeps when not
in use.

RS-232 receive error.

Normal during host reset. Otherwise,
set the digital scanner's RS-232 parity
to match the host setting.

Digital scanner emits low/high
beeps during programming.

Input error or

Cancel

bar code

was scanned.

Scan the correct numeric bar codes
within range for the parameter
programmed.

Digital scanner emits
low/high/low/high beeps during
programming.

Out of ADF parameter storage
space.

Erase all rules and re-program with
shorter rules.

Digital scanner emits low/high/low
beeps.

Clearing Code 39 buffer.

Normal when scanning the Code 39
Buffering

Clear Buffer

bar code or

upon attempt to transmit an empty
Code 39 buffer.

Digital scanner emits a power-up
beep after changing USB host type.

The USB bus re-established
power to the digital scanner.

Normal when changing USB host type.

Digital scanner emits one high beep
when not in use.

In RS-232 mode, a <BEL>
character was received and Beep
on <BEL> option is enabled.

Normal when

Beep on <BEL>

enabled and the digital scanner is in
RS-232 mode.

Table 3-1

Troubleshooting (Continued)

Problem

Possible Causes

Possible Solutions

Содержание Symbol DS3407





















































































































































































































































































































































































































Результаты поиска

Содержание Symbol DS3407

Отзывы:

Бренды по названию

Популярные бренды

Motorola Symbol DS3407, Справочное руководство

Результаты поиска

Содержание Symbol DS3407

Отзывы:

Бренды по названию

Популярные бренды