background image

Regulatory Information 

Federal Communications Commission Radio and Television Interface Statement for a Class ‘B’ 
Device 

This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference in the residential installation. This equipment generates, uses and can 
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio communications. However, there is no guarantee that interference 
will not occur in a particular installation. 

If the equipment does cause harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try to correct the interference 
by one of the following measures: 

 

Increase the separation between the equipment and the affected receiver 

 

Connect the equipment on a circuit different from the one the receiver is on 

 

Ensure that the cover plate for the security card is secured and tight 

Changes or modification not expressly approved by the party responsible for compliance could void the 
user’s authority to operate the equipment.

 

Declaration of Conformity 

According to 47 CFR, Parts 2 and 15 for Class B Personal Computers and Peripherals; and/or CPU 
Boards and Power Supplies used with Class B Personal Computers, Motorola, Inc., 6450 Sequence 
Drive, San Diego, CA 92121, 1-800-225-9446, declares under sole responsibility that the product 
identifies with 47 CFR Part 2 and 15 of the FCC Rules as a Class B digital device. Each product 
marketed is identical to the representative unit tested and found to be compliant with the standards. 
Records maintained continue to reflect the equipment being produced can be expected to be within the 
variation accepted, due to quantity production and testing on a statistical basis as required by 47 CFR 
2.909. Operation is subject to the following condition: This device must accept any interference received, 
including interference that may cause undesired operation. The above named party is responsible for 
ensuring that the equipment complies with the standards of 47 CFR, Paragraphs 15.101 to 15.109. The 
Class B digital apparatus meets all requirements of the Canadian Interface Causing Equipment 
Regulations. 

U.S. GOVERNMENT RESTRICTED RIGHTS 

The Product and documentation is provided with RESTRICTED RIGHTS. The use, duplication or 
disclosure by the Government is subject to restrictions as set forth in subdivision (c)(1)(ii) of The Rights 
in Technical Data and Computer Software clause at 52.227-7013. The contractor/manufacturer is 
Motorola, Inc., Broadband Communications Sector, 101 Tournament Drive, Horsham, PA 19044. 

Canadian Compliance 

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B 
est conformé a la norme NMB-003 du Canada. 

 

 

 

 

 

 

 

 

 

 

 

 

 

Содержание QIP2500 Series





























Отзывы: