manualshive.com logo in svg

Motorola ONCE SC140, Примечание к применению, Страница: 24 / 28

Поделиться
Скачать
Motorola ONCE SC140 Скачать руководство пользователя страница 24

A-2

Using the SC140 Enhanced OnCE Stopwatch Timer

Code A-2.   EOnCE_registers.h

/*   EOnCE registers */
#define EXCP_TABLE 0x7000
#define REG_BASE_ADDRESS 0x00effe00         /* EOnCE Status register */

#ifdef COMPILER_BETA_1_BUG
long  EE_CTRL       =         REG_BASE_0x18; /* EOnCE EE pins Control register */
long  EDCA1_CTRL    =         REG_BASE_0x44; /* EOnCE EDCA #1 Control register */
long  EDCA1_REFA    =         REG_BASE_0x64; /* EOnCE EDCA #1 Reference Value A */
long  EDCA1_REFB    =         REG_BASE_0x84; /* EOnCE EDCA #1 Reference Value B */
long  EDCA1_MASK    =         REG_BASE_0xc4; /* EOnCE EDCA #1 Mask Register */
long  ECNT_CTRL     =         REG_BASE_0x100; /* EOnCE Counter Control register */
long  ECNT_VAL      =         REG_BASE_0x104; /* EOnCE Counter Value register */
long  ECNT_EXT      =         REG_BASE_0x108; /* EOnCE Extension Counter Value */
#else
#define  EMCR                   REG_BASE_0x4 /* EOnCE Monitor and Control register */
#define  ERCV                   REG_BASE_0x8 /* EOnCE Receive register */
#define  ETRSMT0                REG_BASE_0x10 /* EOnCE Receive register */
#define  ETRSMT1                REG_BASE_0x14 /* EOnCE Receive register */
#define  EE_CTRL                REG_BASE_0x18 /* EOnCE EE pins Control register */
#define  PC_EX                  REG_BASE_0x1c /* EOnCE Exception PC register */
#define  EDCA0_CTRL             REG_BASE_0x40 /* EOnCE EDCA #0 Control register */
#define  EDCA1_CTRL             REG_BASE_0x44 /* EOnCE EDCA #1 Control register */
#define  EDCA2_CTRL             REG_BASE_0x48 /* EOnCE EDCA #2 Control register */
#define  EDCA3_CTRL             REG_BASE_0x4c /* EOnCE EDCA #3 Control register */
#define  EDCA4_CTRL             REG_BASE_0x50 /* EOnCE EDCA #4 Control register */
#define  EDCA5_CTRL             REG_BASE_0x54 /* EOnCE EDCA #5 Control register */
#define  EDCA0_REFA             REG_BASE_0x60 /* EOnCE EDCA #0 Reference Value A */
#define  EDCA1_REFA             REG_BASE_0x64 /* EOnCE EDCA #1 Reference Value A */
#define  EDCA2_REFA             REG_BASE_0x68 /* EOnCE EDCA #2 Reference Value A */
#define  EDCA3_REFA             REG_BASE_0x6c /* EOnCE EDCA #3 Reference Value A */
#define  EDCA4_REFA             REG_BASE_0x70 /* EOnCE EDCA #4 Reference Value A */
#define  EDCA5_REFA             REG_BASE_0x74 /* EOnCE EDCA #5 Reference Value A */
#define  EDCA0_REFB             REG_BASE_0x80 /* EOnCE EDCA #0 Reference Value B */
#define  EDCA1_REFB             REG_BASE_0x84 /* EOnCE EDCA #1 Reference Value B */
#define  EDCA2_REFB             REG_BASE_0x88 /* EOnCE EDCA #2 Reference Value B */
#define  EDCA3_REFB             REG_BASE_0x8c /* EOnCE EDCA #3 Reference Value B */
#define  EDCA4_REFB             REG_BASE_0x90 /* EOnCE EDCA #4 Reference Value B */
#define  EDCA5_REFB             REG_BASE_0x94  /* EOnCE EDCA #5 Reference Value B */
#define  EDCA0_MASK             REG_BASE_0xc0  /* EOnCE EDCA #0 Mask Register */    
#define  EDCA1_MASK             REG_BASE_0xc4  /* EOnCE EDCA #1 Mask Register */    
#define  EDCA2_MASK             REG_BASE_0xc8  /* EOnCE EDCA #2 Mask Register */    
#define  EDCA3_MASK             REG_BASE_0xcc  /* EOnCE EDCA #3 Mask Register */    
#define  EDCA4_MASK             REG_BASE_0xd0  /* EOnCE EDCA #4 Mask Register */   
#define  EDCA5_MASK             REG_BASE_0xd4  /* EOnCE EDCA #5 Mask Register */    
#define  EDCD_CTRL              REG_BASE_0xe0  /* EOnCE EDCD Control register */    
#define  EDCD_REF               REG_BASE_0xe4  /* EOnCE EDCD Reference Value */     
#define  EDCD_MASK              REG_BASE_0xe8  /* EOnCE EDCD Mask register */    
#define  ECNT_CTRL              REG_BASE_0x100  /* EOnCE Counter Control register */
#define  ECNT_VAL               REG_BASE_0x104  /* EOnCE Counter Value register */
#define  ECNT_EXT               REG_BASE_0x108  /* EOnCE Extension Counter Value */ 
#define  ESEL_CTRL              REG_BASE_0x120  /* EOnCE Selector Control register */
#define  ESEL_DM                REG_BASE_0x124  /* EOnCE Selector DM Mask */         
#define  ESEL_DI                REG_BASE_0x128  /* EOnCE Selector DI Mask */         
#define  ESEL_RST               REG_BASE_0x12c  /* EOnCE Selector RST Mask */         
#define  ESEL_ETB               REG_BASE_0x130  /* EOnCE Selector ETB Mask */         
#define  ESEL_DTB               REG_BASE_0x134  /* EOnCE Selector DTB Mask */         
#define  TB_CTRL                REG_BASE_0x140  /* EOnCE Trace Buffer Control register */
#define  TB_RD                  REG_BASE_0x144  /* EOnCE Trace Buffer Read Pointer */    
#define  TB_WR                  REG_BASE_0x148  /* EOnCE Trace Buffer Write Pointer */   
#define  TB_BUFF                REG_BASE_0x14c  /* EOnCE Trace Buffer */
#define  TRAP_EXCP              EXCP_TABLE  /* trap instruction exception */ 
#define  ILL_EXCP               EXC0x80  /* illegal set or illegal instruction exception */ 
#define  DBG_EXCP               EXC0xc0  /* debug exception (eonce) */ 
#define  OVFL_EXCP              EXC0x100  /* overflow exception */ 
#define  AUTO_NMI_EXCP          EXC0x180  /* default nmi exception vector */
#define  AUTO_EXT_EXCP          EXC0x1c0  /* default external exception */ 
#define  NMI_EXCP               EXC0x280  /* nmi exception vector (arbitrary address) */
#define  EXT_EXCP               EXC0x2c0  /* external exception  (arbitrary address) */
#endif

Содержание ONCE SC140





























Отзывы:

Нет отзывов