Motorola MVME3600 Series Скачать руководство пользователя страница 260 | Manualshive

Страница: 260 / 275

background image

5-14

Computer Group Literature Center Web Site

Programming Details

5

Processor/Memory Domain

The MPC604 processor can operate in both big-endian and little-endian
mode. However, it always treats the external processor/memory bus as
big-endian by performing address rearrangement and reordering when
running in little-endian mode.

The MPC registers inside Raven, the registers inside the Falcon chipset,
the DRAM, the ROM/Flash and the system registers always appear as big-
endian.

Raven’s Involvement

Since PCI is little-endian, the Raven performs byte swapping in both
directions (from PCI to memory and from the processor to PCI) to
maintain address invariance when it is programmed to operate in
big-endian mode with the processor and the memory subsystem.

In little-endian mode, it reverse-rearranges the address for PCI-bound
accesses and rearranges the address for memory-bound accesses (from
PCI). In this case, no byte swapping is done.

PCI Domain

The PCI bus is inherently little-endian and all devices connected directly
to PCI will operate in little-endian mode, regardless of the mode of
operation in the processor’s domain.

PCI-SCSI

SCSI is byte stream oriented with the byte having the lowest address in
memory being the first one to be transferred regardless of the endian mode.
Since address invariance is maintained by the Raven in both little-endian
and big-endian mode, there should be no endian issues for the SCSI data.
Big-endian software must still however be aware of the byte-swapping
effect when accessing the registers of the PCI-SCSI device.

«
...
258
259
260
261
262
...
»

Содержание MVME3600 Series




















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MVME3600 Series

Бренд: M-Audio Страницы: 10

Бренд: Lattice Semiconductor Страницы: 15

iCE40 UltraLite

Бренд: Lattice Semiconductor Страницы: 13

Бренд: Paradyne Страницы: 2

Бренд: Ruckus Wireless Страницы: 102

EdgeLens INT10G8LR56

Бренд: Garland Страницы: 30

LinkStation Mini

Бренд: Buffalo Страницы: 71

Бренд: XJTAG Страницы: 9

Бренд: Xilinx Страницы: 8

Бренд: Aurora Страницы: 6

Power System S914

Бренд: IBM Страницы: 48

Бренд: Camozzi Страницы: 22

Бренд: Proxim Страницы: 65

Бренд: Datacom Страницы: 45

Бренд: Iomega Страницы: 32

Бренд: Dragonchip Страницы: 27

Бренд: Extron electronics Страницы: 1

Бренд: Crestron Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды