manualshive.com logo in svg

Motorola MPC860 PowerQUICC, Руководство пользователя

"Motorola MPC860 PowerQUICC" - отличный продукт для тех, кто ищет высококачественный процессор. У нас вы можете найти бесплатное руководство пользователя. Скачайте его с нашего сайта и руководствуйтесь руководством для оптимальной производительности и эффективности. manualshive.com - ваш источник полезной информации для вашего продукта.

Поделиться
Скачать
background image

MOTOROLA

Chapter  27.  SCC BISYNC Mode

  

27-3

Part V. The Communications Processor Module

interrupt is issued according to TxBD[I]. TxBD[I] controls whether interrupts are generated
after transmission of each buffer, a speciÞc buffer, or each block. The controller then
proceeds to the next BD.

If no additional buffers have been sent to the controller for transmission, an in-frame
underrun is detected and the controller starts sending syncs or idles. If the controller is in
transparent mode, it sends DLE-sync pairs. Characters are included in the block check
sequence (BCS) calculation on a per-buffer basis. Each buffer can be programmed
independently to be included or excluded from the BCS calculation; thus, excluded
characters must reside in a separate buffer. The controller can reset the BCS generator
before sending a speciÞc buffer. In transparent mode, the controller inserts a DLE before
sending a DLE character, so that only one DLE is used in the calculation.

27.3  SCC BISYNC Channel Frame Reception

Although the receiver is designed to work with almost no core intervention, the user can
intervene on a per-byte basis if necessary. The receiver performs CRC16, longitudinal
(LRC) or vertical redundancy (VRC) checking, sync stripping in normal mode, DLE-sync
stripping, stripping of the Þrst DLE in DLE-DLE pairs in transparent mode, and control
character recognition. Control characters are discussed in Section 27.6, ÒSCC BISYNC
Control Character Recognition.Ó

When enabled, the receiver enters hunt mode where the data is shifted into the receiver shift
register one bit at a time and the contents of the shift register are compared to the contents
of DSR[SYN1, SYN2]. If the two are unequal, the next bit is shifted in and the comparison
is repeated. When registers match, hunt mode is terminated and character assembly begins.
The controller is character-synchronized and performs SYNC stripping and message
reception. It reverts to hunt mode when it receives an 

ENTER

 

HUNT

 

MODE

 command, an error

condition, or an appropriate control character.

When receiving data, the controller updates the BCS bit in the BD for each byte transferred.
When the buffer is full, the controller clears the E bit in the BD and generates an interrupt
if the I bit in the BD is set. If incoming data exceeds the buffer length, the controller fetches
the next BD; if E is zero, reception continues to its buffer.

When a BCS is received, it is checked and written to the buffer. The BISYNC controller
sets the last bit, writes the message status bits into the BD, clears the E bit, and then
generates a maskable interrupt, indicating that a block of data was received and is in
memory. The BCS calculations do not include SYNCs (in nontransparent mode) or
DLE-SYNC pairs (in transparent mode).

Note that GSMR_H[RFW] should be set for an 8-bit-wide receive FIFO for the BISYNC
receiver. See Section 22.1.1, ÒGeneral SCC Mode Register (GSMR).Ó

Содержание MPC860 PowerQUICC



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC860 PowerQUICC

CAME Z Series Technical Documentation Manual preview
Z Series
Бренд: CAME Страницы: 16
Ultrak KEGS5000 User Manual preview
KEGS5000
Бренд: Ultrak Страницы: 41
Zander Aachen ZX Series Quick Start Manual preview
ZX Series
Бренд: Zander Aachen Страницы: 10
Zander Aachen SCB Series Operating Instructions Manual preview
SCB Series
Бренд: Zander Aachen Страницы: 44
Zamel Extra Free ROB-01/12-24V Manual Instruction preview
Extra Free ROB-01/12-24V
Бренд: Zamel Страницы: 2
Ezodo 4801P Manual preview
4801P
Бренд: Ezodo Страницы: 7
Sonos Controller CR100 Quick Setup Instructions Manual preview
Controller CR100
Бренд: Sonos Страницы: 12
Freescale Semiconductor RS08 Designer Reference Manual preview
RS08
Бренд: Freescale Semiconductor Страницы: 34
Matelec FPC-12720 Quick Start Manual preview
FPC-12720
Бренд: Matelec Страницы: 2
QSC TSC-101-G3 User Manual preview
TSC-101-G3
Бренд: QSC Страницы: 13
Watt Stopper MRDS10 Installation Instructions preview
MRDS10
Бренд: Watt Stopper Страницы: 3
VADDIO HOT-SHOT Installation And User Manual preview
HOT-SHOT
Бренд: VADDIO Страницы: 16
Sices GC315 User And Installation Manual preview
GC315
Бренд: Sices Страницы: 8
Dasko Electronic DSS2 T-BIS_P Manual preview
DSS2 T-BIS_P
Бренд: Dasko Electronic Страницы: 4
Taco Electronic Solutions iWorx ZXU1 Installation Manual preview
iWorx ZXU1
Бренд: Taco Electronic Solutions Страницы: 24
oventrop Hydromat DP DN 20 Operating Instructions Manual preview
Hydromat DP DN 20
Бренд: oventrop Страницы: 40
Air Torque AT1001U Maintenance Manual preview
AT1001U
Бренд: Air Torque Страницы: 11
Paradox Imperial ACM24D Manual preview
Imperial ACM24D
Бренд: Paradox Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды