Motorola MOTO U9 Скачать руководство пользователя страница 9

Страница: 9 / 48

6809513A81-A

April 01, 2008

Level 1 and 2 Service Manual

Specifications

General Function

Specification

Frequency Range GSM 850

824-848 MHz Tx

869-893 MHz Rx

Frequency Range GSM 900

880-915 MHz Tx (with EGSM)

925-960 MHz Rx

Frequency Range DCS 1800

1710-1785 MHz Tx

1805-1880 MHz Rx

Frequency Range PCS 1900

1850-1910 MHz Tx

1930-1990 MHz Rx

Channel Spacing

200 KHz

Channels

174 EGSM, 374 DCS, 299 PCS, 124 GSM 850 carriers (8 channels per carrier)

Modulation

GMSK at BT=0.3

Transmitter Phase Accuracy

5 Degrees RMS, 20 Degrees peak

Duplex Spacing

45MHz (GSM 850, GSM 900), 95MHz (DCS 1800), 80MHz (PCS 1900)

Frequency Stability

+/-0.10 ppm of the downlink frequency (Rx)

Operating Voltage

+3.35Vdc to +4.35Vdc (Battery)

+5.00Vdc max (external connector)

Transmit Current Drain

60-290 mA average talk current drain

Standby Current Drain

~3 mA (DRX2), 2 mA (DRX9) typical

Temperature Range

-10 degC to +55 degC (+15 deg F to +130 deg F)

Dimensions, with 900 mAh Li-Ion battery

50mm x 87.5mm x 22.7mm

Size (Volume)

55-60 cc

Weight

103 grams with battery

Battery Life, with standard 900mAh Li-

Ion Battery

GSM

Talk time Up to 400 mins

Standby time Up to 250 hrs

All talk and standby times are approximate and depend on network configuration,

signal strength, and features selected. Standby times are quoted at DRX=2 to

DRX=9.

Talk times are quoted as a range from DTX off to DTX on.

Battery Charge Time

3 hours to 95% of 900mAh capacity

Alert Volume

Max 95dB @ 5cm, 0.5 Watts input

Transmitter Functions

Specification

RF Power Output

32.5 dBm nominal (GSM 850/900)

29.5 dBm nominal (DCS1800/PCS1900)

Output Impedance

50 ohms nominal

Spurious Emissions

-36dBm from 0.03 to 1 GHz, -30dBm from 1 to 4 GHz

Receiver Functions

Specification

Receive Sensitivity

Better than -103dBm

Rx Bit Error Rate (100k bits) Type II

< 2%

Содержание MOTO U9

















































Результаты поиска

Содержание MOTO U9

Отзывы:

Бренды по названию

Популярные бренды

Motorola MOTO U9, Руководство по обслуживанию

Результаты поиска

Содержание MOTO U9

Отзывы:

Бренды по названию

Популярные бренды