Motorola M-CORE MMC2001 Series Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 259

background image

MOTOROLA

EXTERNAL INTERFACE MODULE

MMC2001

7-10

REFERENCE MANUAL

OEA — OE Assert

This bit determines when OE is asserted during a read cycle. If WSC=0000, this bit is
ignored and OE is asserted for one half of a clock cycle only. If EBC in the corre-
sponding register is cleared, then the EB[0:1] outputs are similarly affected.

0 =

OE is asserted normally, i.e., as early as possible.

1 =

OE is asserted one half of a clock cycle later during a read cycle to this chip
select address space. The cycle length and write cycles are not affected.

WEN — EB Negate

This bit is used to determine when EB[0:1] outputs are negated during a write cycle.
This is useful to meet data hold time requirements for slow memories. If WSC=0000,
this bit is ignored and EB[0:1] outputs are asserted for one half of a clock cycle only.

0 =

EB[0:1] are negated normally, i.e., as late as possible.

1 =

EB[0:1] are negated one half of a clock cycle earlier during a write cycle to
this chip select address space. The cycle length and read cycles are not
affected.

EBC — Enable Byte Control

This bit is used to indicate which access types are allowed to assert the enable byte
outputs (EB[0:1]).

0 =

Read and write accesses are both allowed to assert the EB[0:1] outputs,
thus configuring them as byte enables.

1 =

Only write accesses are allowed to assert the EB[0:1] outputs, thus configur-
ing them as byte write enables. The EB[0:1] outputs must be configured as
byte write enables for accesses to dual x8 memories.

DSZ — Data Port Size

This field defines the width of the device data port.

SP — Supervisor Protect

This bit is used to restrict accesses to the address range defined by the correspond-
ing chip select if the access is attempted in the user mode of CPU operation.

0 =

User mode accesses are allowed in this chip select address range.

1 =

User mode accesses are prohibited. An attempted access to an address
mapped by this chip select in user mode will result in a TEA to the CPU and
no assertion of the chip select output.

Table 7-5 Data Port Size Field Settings

Value

Meaning

00

8-bit port, resides on DATA[15:8] pins

01

8-bit port, resides on DATA[7:0] pins

10

16-bit port

11

Reserved

Freescale Semiconductor,

I

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

nc.

..

«
...
59
60
61
62
63
...
»

Содержание M-CORE MMC2001 Series




































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для M-CORE MMC2001 Series

Smart-MPPT Li Series

Бренд: Y-Solar Страницы: 6

Бренд: Fairchild Страницы: 2

Бренд: Panasonic Страницы: 31

Бренд: Panasonic Страницы: 31

Бренд: NAiS Страницы: 199

Бренд: Panasonic Страницы: 38

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 179

Бренд: Panasonic Страницы: 23

Бренд: Paratec Страницы: 8

Бренд: J+J Страницы: 33

Бренд: ZKTeco Страницы: 2

Бренд: FASAR ELETTRONICA Страницы: 2

Бренд: Faro Страницы: 3

Бренд: YASKAWA Страницы: 456

Бренд: Ascon tecnologic Страницы: 16

Бренд: KIOUR Страницы: 3

Optidrive Elevator

Бренд: Invertek Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды