manualshive.com logo in svg

Motorola E815, Руководство по обслуживанию, Страница: 8 / 48

Поделиться
Скачать
Motorola E815 Скачать руководство пользователя страница 8

8

 

 

        January 24, 2006 

6809492A18-B

Specifications

 E815, E816 CDMA

Specifications  

 

General Function 

Specification 

Frequency Range 1900 MHz PCS

1931.250 -1988.750 MHz Rx
1851.250 -1908.750 MHz Tx

Frequency Range 800 MHz CDMA 

869.04 - 893.97 Rx
824.04 - 848.97 Tx

Channel Spacing

50 kHz PCS
30 kHz CDMA

Channels

1200 PCS
832 CDMA

Modulation

1M25D1W (1.25 MHz bandwidth) CDMA
3G1XRTT (1.25 MHz bandwidth) CDMA-1X

Transmitter Phase Accuracy?

5 Degrees RMS, 20 Degrees peak

Duplex Spacing

80 MHz PCS

Frequency Stability

± 300 Hz (CDMA) 
± 2.5 ppm (CDMA)

Power Supply

3.6V Li Ion 750 mAh battery

Average Transmit Current

310 mA at +13 dBm)

Average Stand-by Current

3.40 mA 

Dimensions 
(with 750 mAh Li ion battery)

94.3mmX49.6mmX24.4mm 
3.7 in. x 1.9 in. x 0.9 in.

Size (Volume)

88 cc (5.37 in.

3

) without antenna

Weight

<132g (4.65 oz) with battery

Temperature Range

-30° C to +60° C (-22° F to +140° F)

Humidity

80% Relative Humidity at 50° C (122° F)

Battery Life, 750 mAh Li Ion Battery

Up to 180 minutes digital talk time (IS 95 A/B) 
Up to 250 hours (IS 95 A/B) standby time
Up to 350 hours (IS 2000) standby time

All talk and standby times are approximate and 
depend on network configuration, signal strength, 
and features selected.

Transmitter Function 

Specification

RF Power Output

0.20 watts -23 dBm into 50 ohms (CDMA 
nominal) 

Input/Output Impedance

50 ohms (nominal)

Transmit Audio Response

6 dBm/octave pre-emphasis

Modulation

1M25DIW (1.25 MHz bandwidth) CDMA

CDMA Transmit Waveform Quality 
(Rho)

0.94

Receiver Function 

Specification

Receive Sensitivity

-104 dBm (CDMA, 0.5% Static FER) 0.5% or less 

Audio Distortion

Less than 5% at 1004 Hz, +/- 8 kHz peak 
frequency deviation (transmit and receive)

Adjacent and Alternate Channel 
Desensitization

3% BER max at 107 dBm signal; -94 dBm/30 kHz, 
-65 dBm/60 kHz

Содержание E815

















































Отзывы:

Нет отзывов