manualshive.com logo in svg

Motorola DragonBall MC68328, Руководство пользователя

Поделиться
Скачать
Motorola DragonBall MC68328 Скачать руководство пользователя страница 115

 

UART 

 

 

8-12

 

MC68328 DRAGONBALL PROCESSOR USER’S MANUAL

 

MOTOROLA

 

DATA

These bits are the parallel transmit-data inputs. While in 7-bit mode, D7 is ignored. While
in 8-bit mode, all bits are used. Data is transmitted LSB first. A new character is transmit-
ted when these bits are written. These bits read as 0.

 

8.2.9 Miscellaneous Register

 

This register contains miscellaneous bits to control test features of the UART block. Some
bits are intended for factory use only and should not be disturbed by users.

RSVD

These bits are reserved and should remain 0.

CLK SRC

This bit selects the source of the 1x bit clock for transmit and receive. While high, the bit
clock is derived directly from the GPIO pin (it must be configured as an input.) While low,
(normal) the bit clock is supplied by the baud generator. This bit allows high-speed syn-
chronous applications where a clock is provided by the external system.

0 = Bit clock generated by baud generator
1 = Bit clock supplied from GPIO (input)

FORCE PERR

While high, this bit forces the transmitter to generate parity errors if parity is enabled. This
bit is provided for system debugging.

0 = Generate normal parity
1 = Generate inverted parity (error)

LOOP

This bit controls loopback for system-test purposes. While this bit is high, the receiver in-
put is internally connected to the transmitter and ignores the RXD pin. The transmitter is
unaffected by this bit. The receiver can be in either clock mode (16x or 1x) for proper op-
eration.

0 = Normal receiver operation
1 = Internally connect transmitter output to receiver input

RTS CONT

RTS Control

This bit selects the function of the RTS pin.

0 = RTS pin is controlled by the RTS bit
1 = RTS pin is controlled by the receiver FIFO. When the FIFO is full (one slot remain-

ing) RTS is negated.

 

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

RSVD

CLK 

SRC

FORCE 

PERR

LOOP

RSVD

RTS 

CONT

RTS

IRDA 

ENABLE

IRDA 

LOOP

UNUSED

ADDRESS: $(FF)FFF908

Reset Value: $0000

 

Figure 8-6. Miscellaneous Register

Содержание DragonBall MC68328










































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды