Motorola DigitalDNA ColdFire MCF5272 Скачать руководство пользователя страница 473 | Manualshive

Страница: 473 / 550

background image

Chapter 20. Bus Operation

20-21

Interrupt Cycles

longword is misaligned at an address that is not evenly divisible by four. However, because
operands can reside at any byte boundary, they can be misaligned.

Although the MCF5272 does not enforce any alignment restrictions for data operands
(including program counter (PC) relative data addressing), significant performance
degradation can occur when additional bus cycles are required for longword or word
operands that are misaligned. For maximum performance, data items should be aligned on
their natural boundaries. All instruction words and extension words must reside on word
boundaries. An address error exception occurs with any attempt to prefetch an instruction
word at an odd address.

The MCF5272 converts misaligned operand accesses to a sequence of aligned accesses.
Figure 20-18 illustrates the transfer of a longword operand from a byte address to a 32-bit
port, requiring more than one bus cycle. Figure 20-19 is similar to the example illustrated
in Figure 20-18 except that the operand is word-sized and the transfer requires only two bus
cycles.

Figure 20-18. Example of a Misaligned Longword Transfer

Figure 20-19. Example of a Misaligned Word Transfer

20.9 Interrupt Cycles

All interrupt vectors are internally generated. The MCF5272 does not support external
interrupt acknowledge cycles. The System Integration Module prioritizes all interrupt
requests and issues the appropriate vector number in response to an interrupt acknowledge
cycle. Refer to the System Integration chapter for details on the interrupt vectors and their
priorities.

When an external peripheral device requires the services of the CPU, it can signal the
ColdFire core to take an interrupt exception. The external peripheral devices use the
interrupt request signals (INTx) to signal an interrupt condition to the MCF5272. The
interrupt exception transfers control to a routine that responds appropriately.

There are a total of six external interrupt inputs, INT[6:1]. Depending on the pin
configuration between three and six of these pins are available. Each interrupt input pin is

Transfer 1

Transfer 2

Transfer 3

—

—

Byte 3

Byte 0

—

—

—

Byte 1

—

—

Byte 2

—

31

24 23

16 15

8 7

0

001

010

100

A[2:0]

Transfer 1

Transfer 2

—

Byte 1

—

—

—

—

Byte 0

—

31

24 23

16 15

8 7

0

001

100

A[2:0]

«
...
471
472
473
474
475
...
»

Содержание DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DigitalDNA ColdFire MCF5272

AllShare Cast Dongle

Бренд: Samsung Страницы: 2

Бренд: D-Link Страницы: 14

Бренд: Black Box Страницы: 9

Бренд: Measurement Computing Страницы: 27

Бренд: Barco Страницы: 121

SmartMesh IA-510 D2511

Бренд: Dust Networks Страницы: 30

LBON320AC Series

Бренд: Lindsay Broadband Страницы: 4

EK-FC750 GTX Series

Бренд: ekwb Страницы: 2

Бренд: Aaeon Страницы: 119

KÜHLER H2O 920

Бренд: Antec Страницы: 6

IA611 Xplained Pro

Бренд: Knowles Страницы: 14

Бренд: Magewell Страницы: 10

Бренд: Z3 Technology Страницы: 18

Бренд: Keithley Страницы: 108

Бренд: PairGain Страницы: 48

Бренд: ADLINK Technology Страницы: 95

Бренд: Kordis Страницы: 31

Бренд: ZALMAN Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды