Motorola DigitalDNA ColdFire MCF5272 Скачать руководство пользователя страница 374 | Manualshive

Страница: 374 / 550

background image

16-14

MCF5272 User’s Manual

Register Descriptions

Table 16-9 describes UISRn and UIMRn fields.

16.3.11 UART Divider Upper/Lower Registers (UDUn/UDLn)

The UDUn registers (formerly called UBG1n) hold the MSB, and the UDLn registers
(formerly UBG2n) hold the LSB of the preload value. UDUn and UDLn concatenate to
provide a divider to CLKIN for transmitter/receiver operation, as described in
Section 16.5.1.2.1, “CLKIN Baud Rates.”

Table 16-9. UISRn/UIMRn Field Descriptions

Bits

Name

Description

7

COS

Change-of-state.
0 UIPCRn[COS] is not selected.
1 Change-of-state occurred on CTS and was programmed in UACRn[IEC] to cause an interrupt.

6

ABC

Autobaud calculation.
0 Autobaud is disabled or is waiting for the first receiver character.
1 The baud rate has been calculated and loaded into the clock source divider (UDUn and UDLn).
Once set, this bit is cleared by writing to UCRn[ENAB].

5

RxFIFO

Receiver FIFO status. Once set, this bit is cleared by reading URBn.
0 FIFO status indication is disabled or the receiver status has not changed.
1 The receiver status has changed as programmed in URFn[RXS].

4

TxFIFO

Transmitter FIFO status. Once set, this bit is cleared by reading UTBn.
0 FIFO status indication is disabled or the transmitter status has not changed.
1 The transmitter status has changed as programmed in UTFn[TXS].

3

RxFTO

Receiver FIFO timeout.
0 No receiver FIFO timeout. This bit is cleared by reading all remaining data in the receiver FIFO, by

receiving another character into the FIFO, or if the receiver is disabled. The count to timeout is
restarted when RxFTO is cleared.

1 The receiver FIFO has timed out at 64 baud with unread data below the FIFO fullness level.

2

DB

Delta break.
0 No new break-change condition to report. Section 16.3.5, “UART Command Registers (UCRn),”

describes the

RESET

BREAK

-

CHANGE

INTERRUPT

command.

1 The receiver detected the beginning or end of a received break.

1

FFULL/

RxRDY

RxRDY (receiver ready) if UMR1n[FFULL/RxRDY] = 0; FIFO full (FFULL) if UMR1n[FFULL/RxRDY]
= 1. Duplicate of USRn[FFULL/RxRDY].

0

TxRDY

Transmitter ready. This bit is the duplication of USRn[TxRDY].
0 The transmitter holding register was loaded by the CPU or the transmitter is disabled. Characters

loaded into the transmitter holding register when TxRDY = 0 are not sent.

1 The transmitter holding register is empty and ready to be loaded with a character.

7

0

Field

Divider MSB

Reset

0000_0000

R/W

Write only

Address

MBAR + 0x118 (UDU0), 0x158 (UDU1)

Figure 16-12. UART Divider Upper Registers (UDUn)

«
...
372
373
374
375
376
...
»

Содержание DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DigitalDNA ColdFire MCF5272

Бренд: Data Translation Страницы: 60

Бренд: DBM Страницы: 50

Бренд: LAWO Страницы: 154

WS-650 lite Series

Бренд: Laurell Страницы: 84

Бренд: Maxim Страницы: 14

Бренд: ICP DAS USA Страницы: 8

Бренд: OPTO 22 Страницы: 28

Бренд: RR-Concepts Страницы: 12

Бренд: Omron Страницы: 14

LL140 RGB Series

Бренд: Corsair Страницы: 30

Бренд: AES Страницы: 44

CG9103-2RS232-1USB

Бренд: BiPOM Electronics Страницы: 8

JNLH61S-6C Series

Бренд: JETWAY Страницы: 36

593/25, 593/45, 593/TB, RS-422, RS-485

Бренд: Patton electronics Страницы: 8

Бренд: Hakki Pilke Страницы: 48

Бренд: Maco Страницы: 8

INTEL CORE i5 SYSTEM BOARD

Бренд: Aprotech Страницы: 154

Бренд: Asus Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды