manualshive.com logo in svg

Motorola c18, Руководство разработчика

Поделиться
Скачать
Motorola c18 Скачать руководство пользователя страница 44

Hardware Description

36

 98-08901C63-A

3.9.3

LCD_EL_EN

The c18 provides support for controlling an electro-luminescent (EL) lamp. The output enables four levels of intensity control.

3.9.4

Keypad

The keypad interface consists of eight pins, which can be used to connect a matrix keypad and other control buttons (such as
volume up/down). Each pin asserts an interrupt if pulled low. All keypad lines have internal pull-ups.

3.9.5

General-purpose A/D Converter - GPADC

The c18 has two general-purpose ADC inputs, ADC1 and ADC2. The GPADC is located in the MSM5100 block. It is intended
to digitize DC signals corresponding to analog parameters, such as battery voltage and temperature.

Table 14 lists the GPADC specifications.

*

Vref can be software configured to 0.62 V, 1.24 V, 1.86 V or 2.5 V

.

Table 14. GPADC Specifications

Parameter

Min

Typ

Max

Units

Comments

Resolution

8

Bits

Full-scale error

+/-1

LSB

Offset error

+/-6

LSB

Channel isolation

50

dB

At DC

Full-scale input range

GND

Vref

*

3dB input bandwidth

2.65

MHz

Source resistance = 50 

Ω

Input serial resistance

5

K

Ω

Input capacitance

12

pF

Note

This feature is hardware supported.

Содержание c18



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды