Motorola APX 4000 Скачать руководство пользователя | Manualshive

Страница: 242 / 526

background image

8-2

Basic Troubleshooting

: Operational Error Codes

8.2

Operational Error Codes

During radio operation, the radio performs dynamic tests to determine if the radio is working properly.
Problems detected during these tests are presented as error codes on the radio’s display. The
presence of an error code should prompt a user that a problem exists and that a service technician
should be contacted. Use

to aid in understanding particular operational error codes.

02/88

DSP RAM Fatal Error –

Note:

Not a checksum

failure

Turn the radio off, then on

02/90

General DSP Hardware Failure (DSP startup
message not received correctly)

Turn the radio off, then on

Hardware board absent

Keypad board is not connected properly to the
radio

Ensure the Keypad board is fixed
in place

15/10

External Accessory Non-Fatal Error
External Accessory is not present on power up
or did not power up correctly, and external
accessory feature is enabled in codeplug.

Verify external accessory is
connected and powers up. Turn
the radio off, then on.

15/90

External Accessory Fatal Error
External Accessory is not present on power up
or did not power up correctly, and external
accessory feature is enabled in codeplug.

Verify external accessory is
connected and powers up. Turn
the radio off, then on.

1E/10

Collaborative device is connected to the radio
but the collaborative feature is not enabled in
the codeplug.

Contact your Motorola Sales
Representative/Partner on how to
add Collaborative feature to your
radios.

Note:

If the corrective action does not fix the failure, send the radio to the depot.

Table 8-2. Operational Error Code Displays

Error Code

Description

Corrective Action

FAIL 001

Synthesizer Out-of-Lock

1. Reprogram external codeplug
2. Send radio to depot

FAIL 002

Selected Mode/Zone Codeplug
Checksum Error

Reprogram external codeplug

Table 8-1. Power-Up Error Code Displays (Continued)

Error Code

Description

Corrective Action

«
...
240
241
242
243
244
...
»

Содержание APX 4000















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для APX 4000

Бренд: Handic Страницы: 59

Бренд: JB.lab Страницы: 56

MPD820 - DVD Player - 8

Бренд: Magnavox Страницы: 42

Бренд: CTP Systems Страницы: 4

Бренд: Goodmans Страницы: 12

Бренд: GEARDON Страницы: 3

Бренд: GENTRON Страницы: 33

Бренд: auna Страницы: 76

Бренд: Linden Страницы: 28

Бренд: auna Страницы: 152

Бренд: Uniden Страницы: 4

Бренд: Radio Shack Страницы: 10

ElectroMate VEC097

Бренд: Vector Страницы: 20

Бренд: Power Страницы: 108

Бренд: SOUNDMASTER Страницы: 4

Бренд: Ocean Digital Страницы: 18

Бренд: F.F. Group Страницы: 80

Бренд: Rosenbauer Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды