Motorola A840 - Cell Phone - CDMA2000 1X Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 56

Motorola A840 - Cell Phone - CDMA2000 1X Скачать руководство пользователя страница 41

6809485A78-O

June 07, 2004

43

Level 2 Service Manual

Disassembly

Removing the Display Module

1.

Remove the battery cover, battery, antenna, keypad bezel, speaker cover,
keyboard stiffener, flip assembly, transceiver board, flip display lens, flip
assembly, flip assembly sleeve, flip knuckle, and display module as described
in the procedures.

2.

Use the disassembly tool to disconnect the flex connector from the display
module assembly (see Figure 24).

3.

Carefully, lift the display module up and away from the remainder of the flip
assembly.

4.

To replace, seat the display module back into the flip assembly.

5.

Carefully re-connect the flex connector.

6.

Replace the display bezel, flip knuckle, flip assembly sleeve, flip assembly, flip
display lens, transceiver board, flip assembly, keyboard stiffener, speaker
cover, keypad bezel, antenna, battery, and battery cover as described in the
procedures.

032233o

Figure 24. Removing the Display Module

«
...
39
40
41
42
43
...
»

Содержание A840 - Cell Phone - CDMA2000 1X

























































Отзывы:

Нет отзывов