OPERATING INSTRUCTIONS
Check Engine Hoist
Before any use of your Motorhead Engine Hoist visually
inspect the entire unit including the Support Post,
Hydraulic Ram, and Boom for any loose points, signs
of instability, or leaking hydraulic fluid. If observed low,
add oil as needed. This unit is designed for engine pulling
only. DO NOT attempt to use it for lifting any other heavy
equipment.
Check Weight
Maximum Weight Capacity is 2 TONS. Always check
weight of engine and compare to the unit's capacity.
NEVER EXCEED WEIGHT LIMIT or loss of load may occur.
Check Work Area
Visually inspect the floor surface before use. Make
sure that floor is smooth, hard, free of cracks and
obstructions that could hamper movement of hoist.
STORED VIEW
ASSEMBLY INSTRUCTIONS
BOOM EXTENSION
BOOM
SUPPORT POST
SUPPORT BRACES
HYDRAULIC RAM
"A"FRAME BASE
BASE LEGS
5-LINK CHAIN W/HOOK
BOLT M18X100
BOLT M14X100
BOLT M16X90
BOLT M16X70
BOLT M14X100
BOLT M14X70
BOLT M8 X12
LOCK PIN16
LOCK PIN16
CASTER 3”
CASTER 3-1/2”
PUSH BAR
Wheel 3-1/2”
DESCRIPTION
59" Height
33"
Width
22" Length
H
Prior to starting to build your MOTORHEAD Engine Hoist, separate all parts and bolts from
packing. Become
familiar with each part before preceeding to assemble. See Parts List Below for list of parts
and fasteners.
Step 1 – Install Casters and Wheels
Using two 3 – 1/2” casters (#11) and two 3” casters (#10) to the Frame Base (F).
Using two 3 - 1/2” wheels (#13) to the Base Legs (G).
Step 2 – Build Main Frame Section
A. Slide the Base Legs (G) into the Frame Base (F) and secure with two Lock Pin16
(#8).
B. Place the Support Post (C) on the Frame Base (F) and insert two M14X100 (#5)
bolts. Finger tighten so that the Support Post can be moved in order to attach
the Support Braces (D).
C. Place one Support Brace (D) on each side of the Support Post (C). Secure the
top with one M14 x 100 (#2) bolt and the bottom with two M14 x 100 (#5) bolts.
Then tighten the M18 x 100 (#1) from Step B above.
Step 3 – Install The Hydraulic Ram
Place the Hydraulic Ram (E) on the Support Post (C) bracket. Lean the Hydraulic
Ram against the Support Post and secure at the bottom with one M16 x 90 (#3)
bolt.
Step 4 – Attaching Boom And Extension
A. Place the Boom (B) on top of the Support Post (C) and secure with one M18 x
100 (#1) bolt. Pump Hydraulic Ram (E) until it is extended approximately 2".
Place front mounting bracket on Boom (B) on top of Hydraulic Ram (E) and
secure with one M16 X70 (#4) bolt.
B. Tighten all bolts on Hydraulic Ram (E) from Step 3 and Step 4A.
C. Slide Boom Extension (A) inside of Boom (B) and secure with one Lock Pin16
(#9) in hole MARKED 1 TON.
Step 5 – Completed Assembly
A. Secure Hook and Chain Assembly to Boom Extension with one M14 x 70 (#6)
bolt.
B. Secure one Push Bar (#12) to back of Support Post (C) with four M8 x 12 (#7)
bolts.
Installation is now completed. Make sure you follow Operating Instructions completely for
proper use and use of this product and Lifting Cautions.
A
B
C
D
E
F
G
H
1
2
3
4
5
6
7
8
9
10
11
12
13
PART
NO.
4
5
2 Ton (4,000 Lbs.) Mobile Engine Hoist
(1586250)
2 Ton (4,000 Lbs.) Mobile Engine Hoist
(1586250)
