manualshive.com logo in svg

Motoalliance 46'' Garden Tractor Plow System, Инструкция по эксплуатации

Поделиться
Скачать
Motoalliance 46'' Garden Tractor Plow System Скачать руководство пользователя страница 4

Tilt Pin

Handle Base

Plow Side - Lift Assembly

Mower Side - Lift Assembly

Lift Bracket

R-Clip

1/2" Flat Washer

Tilt Pin

Installation of the Handle Base.

Parts Required: (1) Plow Side - Lift Assembly 

Pre Assembled,

 (1) Mower Side Lift Assembly 

Pre Assembled

, (2) 1/2" Flat Washers, (2) R-Clips, (1) Tilt Pin, 

(1) Handle Base.

Align Holes in Plow Side - Lift Assembly with Holes in Mower Side - Lift Assembly. Slide Tilt Pin thru lower holes and secure on other side with (1) 

1.

1/2" Flat Washer and (1) R-Clip.

Now, Align the Lift Bracket component with the holes as shown in diagram below. Once aligned, slide Handle Base thru entire assembly and align 

2.

holes in both components.

Secure with (2) 5/16" Lynch Pins.

3.

23001 Industrial Blvd, Rogers, MN 55374

  1-866-527-7637 (toll free)

    www.motoalliance.com / [email protected]

4

Содержание 46'' Garden Tractor Plow System














Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды