manualshive.com logo in svg

Motion Composites Helio Kids, Руководство пользователя

Поделиться
Скачать
Motion Composites Helio Kids Скачать руководство пользователя страница 12

T

 (450) 588-6555 - 1 866 650-6555  

F

 (450) 588-0200

[email protected]

12

10.    

Adjustments and 

maintenance of your 

HELIO KIDS 

10.1 

Service

Refer to your dealer for service. A complete and updated list of 
service providers can be found on our website. 

10.2 

Replacement Parts

Ordering information:
Consult our website to download the parts manual and view 
ordering information.

Please contact us at:

Motion Composites Inc.

519 J-Oswald Forest, suite 101
Saint-Roch-de-l’Achigan, Quebec
J0K 3H0 Canada
Phone: 1-866-650-6555
Fax: (450) 588-0200
[email protected]
www.motioncomposites.com

10.3 

Tools needed

The 

HELIO KIDS

 was designed to be serviced with 

regular tools. All screws and bolts are standard and can 
be adjusted with a wrench, socket wrench, or Allen key.  
Motion Composites does not recommend the use of any 
power tools to tighten screws on this wheelchair. Final 
tightening should be done manually.

10.4 

General maintenance

10.4.1 

Tire pressure

•   Check tire pressure with a tire gauge. 
•   Inflate if pressure is below recommended amount as labelled 

on the sidewall. 

•   Do not inflate tire over recommended pressure. 
•   Over inflation could result in tire failure and injury.
•   Under inflation could result in a flat tire.

10.4.2 

Cleaning your wheelchair

•   Use a soft clean cloth with soap and water to clean your 

wheelchair.

•   Rinse and dry the wheelchair adequately. 
•   Do not use abrasive cleaners.
•   Do not use a pressure cleaner.  

10.5 

Backrest

10.5.1 

Removing/Installing the Back Canes

•   Loosen the top bolts and, 

which are also used to 
support the armrest socket 
(Swing Away and Flip Back 
armrest).

•   Slide down the back post to 

remove it from the tube.

•   Reinstall the back post 

in the reverse order and 
tighten screws snugly.

•   Tighten bolts and firmly.
•    Wheelchairs  equipped  with 

Flip Back armrests; tighten 
screw while paying special 
attention to the force 
needed to flip back the 
armrest. 

10.5.2 

Adjusting the Back Angle 

•   Loosen screw (1) and 

remove screw (2) from the 
levelling device. 

•   Adjust to desired angle by 

sliding the mechanism.

•   Reinstall screw (2) and 

tighten both screws to fit 
snugly. 

10.5.3 

Removing/Installing the seat belt 

•   Remove Screw (1) in order to remove the seat belt clamp (2) 

that is attached to the belt

•   Reinstall screw (1) directly on the frame clamp (3)
•   Tighten screw (1) until it is properly tightened.
•   Repeat the same steps on the other side

Содержание Helio Kids

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды