![Motion Composites Helio A6 Скачать руководство пользователя страница 26](http://html.mh-extra.com/html/motion-composites/helio-a6/helio-a6_user-manual_1837792026.webp)
ADJUSTMENTS AND MAINTENANCE – FOLDING WHEELCHAIRS | USER MANUAL
NOTE: If you ignore these warnings or fail to inspect or maintain your wheelchair as directed in the manual, you may fall, tip over or lose control of the wheelchair and seriously injure yourself or others and damage the
wheelchair.
26
– Hold the axle with a wrench at the other end (near the detent
balls) and turn the bolt to increase the length or tighten to
shorten the axle.
– Reinstall the pull button onto the wheel and in the axle bushing
receiver on the wheelchair.
– To ensure a secure lock, the quick-release locking balls must
extend beyond the axle receiver.
8.11.2 REPLACING/ADJUSTING HANDRIMS
– On the Newton One wheel, the tire may stay in position.
– Use a plastic tire removal tool to take off the tire (1).
– Remove all nuts (2) inside the rim (3).
– Replace the handrim (4) with a new one and align the mounting
holes (5).
– Reinstall and tighten the bolts (2) firmly.
– Reinstall the tire (1) on the rim.
8.11.3 ADJUSTING THE REAR AXLE HEIGHT (VELOCE, C2, A7,
HELIO KIDS, XC2, HELIO)
– Loosen the nut holding the axle bushing (3).
– Move the axle bushing (1) along the mounting plate (2).
– Reinstall the bushing in the desired mounting hole and tighten
nut (3).
8.11.4 ADJUSTING THE REAR AXLE HEIGHT (A6 AND MOVE)
– Remove the nut (3) holding the axle bushing.
– Move the axle bushing (1) along the mounting plate (2).
– Reinstall the bushing in the desired mounting hole and tighten
nut (3).
– On HELIO A6, it is possible to remove the mounting plate and
reverse it to obtain intermediate rear axle height positions.
WARNINGS
The seat height, seat depth, back angle, seating system/
upholstery, size/position of the rear wheels, size/position of
the casters, as well as the user condition directly relate to
the stability of the wheelchair. Any change to any of these
combinations may reduce the wheelchair’s stability. These
adjustments must be performed by a qualified technician.
The seat-to-floor height must have a specific position depend-
ing on the rear wheel size, rear wheel position, front caster
size/position and seat-to-floor angle. These adjustments
must be performed by a qualified technician.
8.11.5 ADJUSTING REAR WHEEL SPACING
– The rear wheels can be adjusted laterally by repositioning axle
receiver (1) on mounting plates (2).
– Loosen nuts (3) on axle receivers (1).
– Position nuts (3) to adjust the spacing.
– Tighten the nuts (3) firmly.
– The nut can be switched from side to side for more adjust-
ments.
8.11.6 CHANGING REAR CAMBER
MICRO-ADJUSTMENT V2 MOUNTING PLATE
– Note the position of face plates (4) on mounting plate.
– Remove nut (1) and lock washer (2) holding the axle bushing
(3).
– Remove the axle bushing (3) along the mounting face plates (4).
– Change or replace the 0° or 3° axle bushing (3).
– Change or replace the 0° or 3° mounting face plates (4) to reach
a 0°, 3° or 6° angle.
– Reinstall axle bushing, mounting face plates, lock washer and
nut at the desired position on the V2 mounting plate.
– Adjust the toe-in / toe-out of rear wheels.
– Tighten the nut (1) on the mounting plate on the right and left
side of the wheelchair.
3
1
2
4
4
STANDARD T2 MOUNTING PLATE
– Note the position of the axle bushing (3) on the mounting plate
– Remove the 2 nuts (1) and lock washer holding the axle bushing
(3).
– Remove axle bushing (3).
– Change or replace the 0° or 3° axle bushing (3).