3
5
7
4
6
8
9
3
5
7
4
6
8 9
10
10
11
11
12
12
13
13
14
14
15
16
17
18
19
20
15
3
5
7
4
6
8
9
3
5
7
4
6
8 9
10
10
11
11
12
12
13
13
15
15
16
16
16
17
17
17
18
18
18
19
20
21
14
21
14
2 LS01 - Maxi Surface
- 1980 - 2011
56 cells wide - 40 cells high
31.75 by 22.5 inches (80.5 by 57 cm)
3
SS02P - Mini Surface Plus
2 Panels - Each panel has 28 cells by 20 cells
Interlocked = 40 cells wide - 28 cells high
22.5 by 15.75 inches (57 by 40 cm)
• Shaded top two rows indicate the larger
size of a Super Mini Surface.
• The Mini and Super Mini have the same
dots and numbers.
• Darkened cell walls are location points
for fixtures that hold the cutting bar.
• If your surface has several black, red and green dots... go to
Step 1.
• If your Surface has only 7 black dots... go to
Step 2.
Step 1...
Removing extra
dots and other markings.
Things you will need:
• Nail Polish Remover • Q-Tips
• Soft lead pencil with eraser.
A...
Locate and mark the 7 black
dotted squares shown in the
diagram... place a small object in
each dotted square to temporarily
mark it.
B...
With nail polish remover in a
small cup, wet the end of a Q-Tip
and dab a small amount on a dot
to be removed... with a clean dry
Q-Tip, wipe out the dot. Using
less remover and clean Q-Tips
works best.
C...
Any other numbers or
marks must be removed before
continuing to Step 2. Remove
any pencil marks with a pencil
eraser and permanent marks with
the nail polish remover.
Step 2...
Using the diagram Surface Model 1 as a guide,
use Option 1 or Option 2 to number your surface.
• Option 1 - Use a soft lead pencil to write in all the numbers.
Darken numbers later with a black Sharpie marker.
• Option 2 - Cut out the numbered squares, from the sheet
provided in your instruction pack, and paste the squares into the
numbered cells including the squares with dots (14 & 21). Use
a small dot of craft glue to paste the squares in place. The blank
squares can be used to cover over old numbers.
Step 3...
Some Surfaces have a thin cell wall in an area where
a Glass Shop fixture must be located. Thin cell walls, on your
Surface, are easy to fix. To check your surface cell walls, use
one of the orange plastic Squaring Blocks.
Super Mini only - Darken this cell wall
Darken this cell wall
Darken cell wall - Mini Surface only
Darken cell wall - Mini Surface only
Surface
Model
2
1
2
1
Preparing a Mini or Super Mini Surface for the PG01B
Preparing a Morton Surface for the PG01B
1 SS02 - Mini Surface
- 1980 - 2011
40 cells wide - 25 cells high
22.5 by 14.25 inches (57 by 36 cm)
1 SM03 - Super Mini
- 2005 - 2011
40 cells wide - 27 cells high
22.5 by 15.375 inches (57 by 39 cm)
Your surface model
- The PG01 used
different reference numbers than the
PG01B. Any Morton Surface will work
but the numbers must be changed to
the PG01B layout. Use the 1 2 3
surface sizes to identify your surface.
Always use the number specific to your
surface model
.
1
1
3
2
1
3
2
1
• Place the center notch over a marked
cell wall. With a Squaring Block set
firmly into the surface, try
to move it to the left and
right. If you have little or no
side movement the cell wall
is correct.
3
3 4
5
7
4
6
8
5 6
8
7
Check all marked
cell walls
If you feel side movement
• Find the included copper foil tape.
• Cut a ½" to ¾" strip of foil, remove
the back and stick the tape to the cell
by folding it over the cell wall.
• Test results with Squaring Block.
Copper
Foil
Marked
cell
Page 2