Morso 1000 Swift Скачать руководство пользователя страница 3

Страница: 3 / 20

1.1 Unpacking the stove

After removing the outer packaging lift the stove and set it carefully in place.

We recommend that two people perform the assembly and installation procedure.

Morsø 1000 The Swift weighs 70 kg.

1.2 Installing the stove

The stove and chimney installations MUST comply to all current National and Local Building Regu-

lations; your approved Morsø dealer or your local building control officer can advise regarding this.

Ultimately, it is you and your installer who is responsible that the installation complies.

1.3 Chimney sweep

It may also be wise to consult your local chimney sweep before installing the stove. After your

stove has been installed, it is advisable to have the chimney checked and swept at least once a

year. In any case, if your chimney has not been used for some time, it should be inspected for

cracking, bird nests, etc. before it is put back into use.

1.4 Stove placement/clearance requirements

Minimum Clearance requirements apply if the stove is placed near to combustible materials.

Permitted clearances to combustible materials are also indicated on the data plate on the

rear of the stove.

1.0 Installing your Morsø stove

Содержание 1000 Swift




















