background image

The Specialist In Drum Handling Equipment

operator’s Manual for Morse < PILot > Power-Propelled Drum Racker Model 910

serial number 267142 to 294520

morsedrum.com

Copyright 2018  -  Morse Mfg. Co., Inc. 

Form OM910 (267142-294520) (Updated August 17, 2018 8:55 AM) 

4

Model 910

Power-Propelled Drum Racker

Lift / Lower and tilt Control Levers (Figure 4.1)

The LIFT CONTROL LEVER, used to lift and lower a drum, is mounted near the 

• 

base of the steering arm. Push lever away from operator to lift a drum, and pull 

lever toward you to lower a drum. 

 

The TILT CONTROL LEVER is also mounted near the base of the steering arm. 

• 

Push lever away from you to tilt the drum to vertical, and pull this lever toward the 

operator to tilt the drum to horizontal.

Battery Disconnect (Figure 4.1)

A battery disconnect is mounted near the rear of the battery compartment. Pulling the 

disconnect removes all power from truck circuits in the event of an emergency.

Parking

When parking the truck, do not obstruct traffic lanes or aisles.

Park the truck in its designated parking area.

1. 

Raise the steering arm until vertical to apply the parking brake.

2. 

Fully lower lift assembly.

3. 

Turn key to off position. Remove key for added security.

4. 

Pull out battery disconnect.

5. 

Also see 

further information

.

 

WARnInG

 - Watch out for pinch points

 

Stay clear of moving parts. Operator should remain behind  

 

the controls during the lift operation.

Figure 4.1

Installation Instructions

The power to the control levers is disabled for shipment. To enable the control 

levers, the customer has to make two wiring connections inside the rear panel on 

the < PILOT > before use.

Connect wiring for LIFT and TILT controls:

Turn the key to OFF position

1. 

Rotate steering arm to one side

2. 

Open cabinet directly below steering arm

3. 

Connect top left wires (figure 4.2)

4. 

Connect bottom right wires (figure 4.3)

5. 

Close cabinet and turn key to the ON position

6. 

Test levers to confirm power connection

7. 

Figure 4.2

Figure 4.3

Содержание PILOT 910








Отзывы: