background image

Copyright 2009  -  Morse Mfg. Co., Inc.   

Form PL400-60 (0604-0309)    (Updated 10/2009) 

 

Page 4

WARNING

 - Watch Out for Pinch Points

Stay clear of moving parts.  Operator should remain behind the push handle during the lift operation.

Floor Lock

The screw-down floor lock is located on the base of the tower 

(figure 3.1).  Turning the floor lock clockwise until it locks in the 

down position activates the floor lock.  When  the floor lock is 

activated it prevents unwanted free wheeling of the unit.  Floor 

conditions determine the effectiveness of the floor lock. The 

operator should verify its holding action before depending on 

it to hold.

Drum Holder Assembly

The drum holder assembly (or “saddle assembly”) is the compo-

nent on the Hydra-Lift Karrier that is intended to hold the drum.  

The drum holder assembly is designed to secure a standard 

ribbed 55-gallon steel drum around it’s middle using a cinch 

chain and ratchet tightening system. The drum holder accepts 

accessories for handling smaller diameter drums.

Operator’s Manual for Morse Hydra-Lift Drum Karrier Model 400A-60

Serial Number 0604 to 0309 (MMYY)

Figure 3.1

The Specialist In Drum Handling Equipment

Model 400A-60

Hydra-Lift, 60”, Manual Lift, Manual Tilt

Содержание Hydra-Lift 400A-60












Отзывы: