background image

The Specialist In Drum Handling Equipment

Model 410-124

Heavy-Duty Hydra-Lift, 72”, Air Power Lift, Manual Tilt

Operator’s Manual for Morse Heavy-Duty Hydra-Lift Karrier Model 410-124

Serial Number 1210 to ____ (MMYY)

morsedrum.com

Copyright 2022 - Morse Mfg. Co., Inc. 

 

Form OM410-124 (1210-____)   (Updated 24 Mar, 2022)

 

5

CAUTION

 

– Do NOT Transport with Drum Raised

ALWAYS LOWER DRUM HOLDER TO LOWEST POSITION BEFORE TRANSPORTING. 

 Unit can 

become unstable when transporting with a raised load.

5.) Lift drum to desired pouring height.  Operate the tilt control as described in 

“Machine Description - Controls”

 to adjust 

the drum attitude.  This is especially important when lifting an open drum.  The floor lock should be engaged while 

dispensing / draining.

6.) When dispensing is complete, tilt drum back to upright position.  Disengage the floor lock and lower the drum to 

transporting height; about 6” (15 cm) off the floor.

WARNING

 - Stay Clear of Raised Drum

NEVER allow anyone to be below any part of a raised drum handler or drum.  Remain behind 

the push handle while handling a drum.

WARNING

 – Do NOT Disengage Cinch Chain When Drum is off the Ground

When drum is in upright position, lower drum to floor before releasing cinch chain.

7.) Push unit to drum storage area and lower drum to floor in upright position.  Release cinch chain from ratchet by applying 

pressure to ratchet handle in a clockwise direction with one hand and opening pawl to free ratchet with the other hand.  

Remove cinch chain link from ratchet.

Figure 3.2

START-UP Procedure

Machine is shipped with hydraulic fluid. 

1. 

Install provided hydraulic control levers (threaded rods with black 

ball handles).

 

2.  IMPORTANT:

 BEFORE operation, remove 

RED

 shipping plug from 

hydraulic reservoir, and replace with provided 

BLACK

 breather.

Operating Instructions

1.)  

Push Hydra-Lift Karrier to drum.

2.)  Using “LIFT” control as described in “

Machine Description - 

Controls

”, position drum holder assembly with back band at 

middle of drum (Figure 3.1).  With ratchet plate swung open 

and cinch chain hanging from chain hook, push unit until back 

band rests firmly against drum.  Some adjustment to tilt angle 

of saddle may be necessary to ensure band fits flush on drum.

3.) 

Attaching the drum:

Drape chain across front of drum and engage a link into notch 

in ratchet (Figure 3.2).  Turn ratchet clockwise to tighten chain.  

If ratchet turns until the pawl is beyond last ratchet tooth, 

turn ratchet back and slide next link into ratchet notch and try 

tightening again.  Chain must be held tightly against drum with 

pawl engaged securely in ratchet teeth.

4.) Operate lift function to lift drum clear of floor.  Roll to 

dispensing location.  NOTE: Do NOT allow drum to impact on 

floor, pouring station, etc. or a spill or damage could occur.

Содержание 410-124







Отзывы: