background image

Copyright 2009  -  Morse Mfg. Co., Inc.   

Form PL400M-96 (0804-0309)   (Updated 12/2009) 

 

Page 4

WARNING

 - Watch Out for Pinch Points

Stay clear of moving parts.  Operator should remain behind the push handle during the lift operation.

Figure 3.2

Floor Lock

The screw-down floor lock is located on the base of the tower 

(figure 3.1).  Turning the floor lock clockwise until it locks in the 

down position activates the floor lock.  When  the floor lock is 

activated it prevents unwanted free wheeling of the unit.  Floor 

conditions determine the effectiveness of the floor lock. The 

operator should verify its holding action before depending on 

it to hold.

Drum Holder Assembly

The drum holder assembly (or “saddle assembly”) is the compo

-

nent on the Hydra-Lift Karrier that is intended to hold the drum.  

The drum holder assembly is designed to secure a standard 

ribbed 55-gallon steel drum around it’s middle using a cinch 

chain and ratchet tightening system. The drum holder accepts 

accessories for handling smaller diameter drums.

Operating Instructions

1.)  Push the Hydra-Lift Karrier to the drum.

2.)  Using the “LIFT” control as described in “

Machine Descrip-

tion - Controls

” (page 3) , position the drum holder assem

-

bly with the back band at the middle of the drum. (Figure 

3.1).  With the ratchet plate swung open and the cinch chain 

hanging from the chain hook, push the unit until the back 

band rests firmly against the drum.  Some adjustment to the 

tilt angle of the saddle may be necessary to ensure band 

fits flush on the drum.

3.) 

Attaching the drum:

Drape the chain across the front of the drum and engage a 

link into the slot in the ratchet (Figure 3.2).  Turn the ratchet 

clockwise to tighten chain.  If ratchet turns until the pawl is 

beyond the last ratchet tooth, turn the ratchet back and slide 

the next link into the ratchet slot and try tightening again.  The 

chain must be held tightly against the drum with the pawl 

engaged securely in the ratchet teeth.

4.)  Operate  the  lift  function  to  lift  drum  clear  of  floor.    Roll 

to dispensing location.  NOTE: Do not allow the drum to 

impact on floor, pouring station, etc. or a spill or damage 

could occur.

Figure 3.1

Operator’s Manual for Morse Hydra-Lift Drum Karrier with Spark Resistant Parts

Model 400AM-96

Serial Number 0804 to 0309 (MMYY)

The Specialist In Drum Handling Equipment

MODEL 400AM-96

Hydra-Lift, 96”, Manual Lift, Manual Tilt

with Spark Resistant Parts

Содержание 400AM-96










Отзывы: