manualshive.com logo in svg

morse 400A-72SS, Руководство оператора, Страница: 5 / 6

Поделиться
Скачать
morse 400A-72SS Скачать руководство пользователя страница 5

The Specialist In Drum Handling Equipment

Model 400A-72SS

Stainless Steel Hydra-Lift, 72”, Manual Lift & Tilt

operator’s Manual for Morse Stainless Steel Hydra-Lift Karrier with Manual Lift and Tilt

Model 400A-72SS  Serial number 1210 to ____ (MMYY)

morsedrum.com

Copyright 2019 - Morse Mfg. Co., Inc. 

Form OM400A-72SS (1210-____)   

(Updated 12 Jun, 2019 11:56 AM)

 

5

Assembly Instructions

Step #1: Place tower on floor, push-handle down. See figure 1.

Step #2: Attach each leg (item 4) using two 3/8-16x3” grade 5 bolts 

(item 2), flat washers (item 3), and lock nuts (item 13) as shown. 

Wheels should be parallel when assembled properly. See figures 

1 & 2.

Please unpack and identify the following parts:

1 ea.   Tower with hydraulic pump and cylinder, etc.

2 ea.   Legs with wheels

1 ea.  Overhead assembly with drum holder, etc.

1 ea.  Package with hardware

NOTE: The clevis pins and mating surfaces at their 

joints should be coated with grease during assembly.

Figure 1

Figure 2

Step #3: Tip the tower up so it stands on the casters and wheels.

Step #4: Lift overhead assembly into position. A drift pin can help align the holes. Insert a greased clevis pin (item 12) through mast cap 

and boom. Install a 5/8” washer (item 9) and 3/16” roll pin (item 8) in the end of the clevis pin. See figure 3.

Step #5: Next, connect the cylinder (item 16) to the overhead assembly: Align ram eye with holes in boom clevis plates and insert a 

greased clevis pin (item 12) with four 5/8” washers (item 9). Place another washer (item 9) on outer end of clevis pin and drive a 3/16” roll 

pin (item 8) into the hole at the end of clevis pin. See figure 4.

Figure 3

Figure 4

Step #6: Remove sealing plug from the top of hydraulic reservoir and fill reservoir with included container of hydraulic fluid. Replace seal

-

ing plug with the included breather plug. Your Hydra-Lift Karrier is now ready for service. Please refer to the operating and maintenance 

instructions provided.

Содержание 400A-72SS







Отзывы:

Нет отзывов