Morris MVF-65374 Скачать руководство пользователя страница 20

20

OPERATION 

Limit the operating time

In  order  to  increase  efficiency,  the  hob  is 
fitted with a operating time limiter for each of 
the cooking zones. The maximum operating 
time is set according to the last heat setting 
selected. 
If you do not change the heat setting for a long 
time (see table) then the associated cooking 
zone  is  automatically  switched  off  and  the 
residual heat indicator is activated. However, 
you  can  switch  on  and  operate  individual 
cooking zones at any time in accordance with 
the operating instructions.

 

Cooking heat 

setting 

 

Maximum operat-

ing time (hours)

1

10

2

5

3

5

4

4

5

3

6

2

7

2

8

2

9

1

The  "H"  residual  heat  indicator  is 
not displayed during a power out-
age. However, cooking zones may 
still be hot!

Residual heat indicator

Heat energy that remains accumulated in the cooking zone after cooking is called the resid-
ual heat. The appliance displays two different levels of residual heat. When a cooking zone 
temperature is above 65°C and the cooking zone or the appliance is switched off, the relevant 
cooking zone display will show the letter "H". Residual heat indication is displayed as long as 
the cooking zone temperature exceeds 65°C.
When a cooking zone temperature is below 65°C the residual heat indication is turned off. 
In the event of power outage when residual heat above 65°C is indicated, the residual heat 
indicator will flash when power is resorted. Residual heat indicator continue to flash until the 
maximum cooling time has elapsed or the cooking zone is selected and used.

When residual heat indicator is 
on, do not touch the cooking 
zone as there is a risk of burns 
and do not place on it any items 
sensitive to heat!

Turn off the appliance

The appliance operates when at least one cooking zone is on. Touch and hold the cooking 
zone selection / On/Off sensor field  (

1

) for about 3 seconds to turn of a desired cooking zone 

or hold the sensor (

1

) for about 5 seconds to turn off the appliance. The letter “H” appears on 

the display (

2

) of the cooking zone the was used, symbolising residual heat. 

Содержание MVF-65374


























Отзывы: