background image

Components of your
iron

⁄ 

Shot of steam button

¤ 

Spray button

‹ 

Variable steam control

› 

Filling hole with cap

fi 

Spray nozzle

Soleplate

‡ 

Illuminated temperature control dial

· 

Water tank

‚ 

Life long anti-scale (certain models only)

„ 

Power on indicator lights - Auto shut-off 

indicator (certain models only)

‰ 

Filling beaker

Before use

Note: The steam facility should only be

used on garments which are suitable for
ironing at the 2 and 3 dot settings.

When ironing with the steam facility at the

2 dot setting, the steam output should be set
at the lower end of the steam range (see
variable steam section).

Textiles and clothes are supposed to

carry ironing instructions. If they don’t you
should follow the fabric guide on page 3, but
be sure to test the temperature by ironing the
hem of the garment or similar area first.

If you turn the control dial down from a

hot setting to a cooler setting, wait until the
iron temperature has stabilised before you
continue ironing.

Filling

1

Make sure that the iron is not plugged in

and then set the variable steam control 

to the ‘0’ position before filling the iron
with water.

2

Open the fill cap and pour water through

the filling hole 

into the water tank 

·

,

using the beaker provided, one beaker full
of water fills the tank (400ml). 

A

After

filling replace the fill cap. In hard water
areas the use of distilled or demineralised
water is recommended.

Never use battery topping up fluid or

water containing any substances like
starch, or sugar, or defrosted water from a
refrigerator.

3

Always pour out the

remaining water
after use. Warning:
When filling your
iron with tap water
always use the
beaker provided.
Never fill directly
under the tap.

Temperature control

Plug in the iron and switch on. The

‘power on’ indicator lights 

situated in the

back cover will illuminate. Set the
temperature control dial 

B

to the

temperature required, but don’t start ironing
immediately. If you wait a few minutes, the
iron will stabilise at the required setting. Your
Morphy Richards iron is fitted with an
indicator light 

which will go on and off

while you are ironing. 

4

¤

·

A

B

turbo steam RN40655 Rev 1  23/7/04  1:34 PM  Page 4

Содержание TURBO STEAM IRON









Отзывы: