manualshive.com logo in svg

Morita Tri auto mini, Инструкции по установке

Поделиться
Скачать
Morita Tri auto mini Скачать руководство пользователя страница 25

Operation   2011-07-05

24

Wipe with Ethanol

Autoclaving the Contra Angle

3

Components Sterilized with Ethanol : Motor Handpiece, Charger, Power Cord, Transmission Cable

Dampen a piece of gauze with ethanol, wring it out and then wipe these components with it.

Never wipe components with any solution other than Ethanol for Disinfection (Ethanol 70 to 80 vol%).  Other solutions could cause cracking and discoloration. 
Never wipe components with a piece of gauze that is excessively wet with ethanol.  It could seep inside the instrument and damage it.  Be especially careful 
around the connection jacks for the transmission cable. 
Avoid spilling chemical solutions used for treatment on the motor handpiece, charger, contra angle or any other components.  These chemicals could damage, 
deform or discolor plastic and metal.  Use extra caution to avoid spilling formalin cresol (FC) and sodium hypochlorite as they are quite strong.  Wipe up any 
chemical spills immediately. (Some chemicals may leave traces even if wiped up immediately).

Take the contra angle out of the paper cup and wipe off any excess oil which may have seeped out.

Dampen a piece of gauze with ethanol, wring it out and then wipe the contra angle with it.
Put the contra angle in a sterilization pouch and autoclave it.

It is highly recommended that instruments be autoclaved in a sterilization pouch (wrapped) or similar device.

Do not use anything except Ethanol for Disinfection (Ethanol 70 to 80 vol%) for cleaning.  Never wipe the contra angle with solutions containing formalin cresol (FC) 
or sodium hypochlorite, which damage plastic; wipe them off immediately if they accidentally get on the contra angle.

Содержание Tri auto mini









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды