mori seiki ZL-153 Скачать руководство пользователя страница 59

Страница: 59 / 561

P-8 DOOR INTERLOCK FUNCTION

The <Part No.> indicates the part number of each component parts. Use these numbers

to order the controls if they are damaged, or if the label become dirty, damaged, or lost.

Volume adjusting knob

<Part No.>
E36013

The knob adjusts buzzer beep volume. Use a fine flat head
screwdriver to turn the adjusting knob from externals.

CW rotation:

Increases volume.

CCW rotation:

Decreases volume.

The knob is set at 40

position in the CW direction from the

minimum volume position.

Do not decrease volume excessively.

If buzzer beeps only faintly, the warning beeps might

not be recognized during interlock release or abnormal

state, constituting hazards.

WARNING label

<Part No.>

Japanese

H45417

English

H45418

German

H45419

French

H45420

Italian

H45421

Spanish

H45422

Portuguese

H45423

Danish

H45424

Dutch

H45425

Swedish

H45426

Norwegian

H45427

Finnish

H45428

Chinese

H45429

The caution label gives information related with the door interlock
function.

Read and follow the instruction printed on the label.

Never remove or make the label dirty.

Place an order with Mori Seiki for the label, if the letters

on the label become dirty, or if the label is damaged or

lost.

Use the WARNING label in the language

understandable to the operators.

No.

Control

Function

Electronic
buzzer

Volume adjusting knob

Warning label

CAUTION

NOTE

Содержание ZL-153


















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ZL-153

Отзывы:

Похожие инструкции для ZL-153

Бренды по названию

Популярные бренды

mori seiki ZL-153, Руководство по эксплуатации

Результаты поиска

Содержание ZL-153

Отзывы:

Похожие инструкции для ZL-153

Бренды по названию

Популярные бренды