![mori seiki MSX-701IV Скачать руководство пользователя страница 162](http://html.mh-extra.com/html/mori-seiki/msx-701iv/msx-701iv_operation-manual_1833981162.webp)
机床操作面板
MACHINE OPERATION PANEL
140
2-3
自动运行按钮
Automatic Operation Buttons
2
注意
2
NOTE
按下自动运行按钮
q
[
开始
]
前,关闭前门和刀库门。
Close the front door and magazine door before pressing the automatic
operation button
q
[START] (Start)
.
自动运行按钮
[
开始
]
Automatic Operation Button [START]
该按钮用于在存储器、
MDI
或
DNC
模式下开始自动运行。
This button is used to start an automatic operation in the
memory, MDI or DNC mode.
8
警告
8
WARNING
注意,当满足了启动自动运行所必须的条件时,如果误按自动
运行按钮
q
[
开始
]
,机床将启动自动运行。
[
机床意外启动
]
Be aware that the machine will start automatic operation if
the automatic operation button
q
[START] (Start) is
pressed by mistake while the conditions required to start
automatic operation are satisfied.
[Unexpected machine start]
1
1
“Conditions for Starting Automatic Operation” (page 125)
在
DNC
模式下,可用外部
I/O
装置(磁带读入机或
个人电脑)运行程序以及运行卡
DNC
操作。
2
注意
1.
外部
I/O
装置(如磁带读入机)是可选的。
2.
若要执行
DNC
模式操作,按以下所示步骤设置数控参
数。
a.
将跨接电缆连接到电气柜中的
RS232C
连接器上。
b.
按下功能选择键
s
(
设定
)
D
[
操作面板
]
D
[
运行模
式
]
,选择运行模式屏幕上的
DNC
模式。
c.
将
I/O
通道设置为
0
。
功能选择键
s
(
设定
)
D
[
参数
]
D
[
设定
]
d.
设置通信参数。(数控参数
No. 101
、
102
、
103
)
功能选择键
l
(
系统
)
D
[NC
系统
]
1•
数控参数设置参见由数控装置制造商提供的手册。
•
卡
DNC
操作(使用用户存储区操作)
)
In the DNC mode, running a program using an
external I/O device (tape reader or personal
computer) and the card DNC operation are possible.
2
NOTE
1. An external I/O device (such as a tape reader) is
optional.
2. To perform DNC mode operation, set the NC
parameters following the steps indicated below.
a.
Connect the cross-cable to the RS232C connector
in the electrical cabinet.
b.
Press the function selection key
s
(SETTING)
D
[OPE. PANEL]
D
[OPE. MODE]
, and select the
DNC mode on the operation mode screen.
c.
Set the I/O channel to 0.
Function selection key
s
(SETTING)
D
[PARAM.]
D
[SETTING]
d.
Set the communication parameters. (NC parameter
No. 101, 102, 103)
Function selection key
l
(SYSTEM)
D
[NC
SYSTEM]
1•
Refer to the manual supplied by NC unit
manufacturer for the NC parameter setting.
•
CARD DNC OPERATION (OPERATION USING
USER MEMORY AREA)(Page 238)
按钮
Button
功能
Function
DNC
START
Содержание MSX-701IV
