Morgan MSG-27MAXIcare Скачать руководство пользователя страница 6

10

11

CLEANING AND MAINTENANCE

TROUBLESHOOTING

This  chapter  summarizes  the  most  common  problems  encountered  with  the

appliance. If you are unable to solve the problem with the information below, contact

your nearest authorized service center.

CLEANING THE SOLE PLATE

Clean the sole plate regularly to move stains.

1.  Insert the power plug into an earthed power supply and press the on/off button to switch

    on the appliance and allow it heat up.

2.  After approx.2 minutes, press the on/off button again to switch off the appliance and 

    detach the power plug from the power supply.

3.  Place a piece of moist cotton cloth on the ironing board.
4.  Iron over the cotton cloth repeatedly to remove stains from the sole plate.

Do not discard the appliance with the normal household waste at the

end  of  its  lifespan,  but  hand  it  in  at  an  official  collection  point  for

recycling. By doing this, you will help to preserve the environment.

STORAGE

1.  Press the on/off button to switch off the appliance 

    and detach the power plug from the power supply. 

2.  Detach the detachable water tank and empty it.
3.  Place the iron on the iron platform.
4.  Turn the carry lock over the tip of the sole plate to 

    lock the iron onto the iron platform.

5.  Fold the supply hose and power cord to store them in

    their respective storage compartments.

6.  You can now easily carry the appliance by the handle

    of the iron with one hand.

Do not carry the appliance by holding the water tank

release lever.

PROBLEM                        POSSIBLE CAUSES                              SOLUTION

The appliance produces           Water is pumped into the boiler inside the           If the pumping sound persists continuously, 

a loud pumping sound.             appliance. This is normal.                                     switch off the appliance and remove the 

                                                                                                                               power plug from the power supply. Contact 

                                                                                                                               your nearest authorized service center.

                                                 There is not enough water in the water tank.       Fill the water tank.
                                                 The appliance is not hot enough to produce        Wait until the iron ready light illuminates

                                                 steam.                                                                   continuously.

The appliance does not            Steam trigger not pressed.                                   Press and hold the steam trigger while 

produce any steam.                                                                                               steam ironing.

                                                 The water tank is not secured properly.               Slide the water tank firmly back into the 

                                                                                                                               appliance’s proper position (click).

                                                 The appliance is not switched on.                        Insert the power plug into the power supply 

                                                                                                                               and press the on/off button to switch on the 

                                                                                                                               appliance.

The appliance has                    The auto-shut-off function is activated                 Press the on/off button to switch on the

switched off.                              automatically when the appliance has not           appliance again.

                                                 been used for more than 10 minutes.

The light in the on/off                The auto-shut-off function is activated                 Press the on/off button to switch on the

button illuminates.                    automatically when the appliance has not           appliance again.

                                                 been used for more than 10 minutes.

Water droplets escape from     When you start steam ironing and in the             This is normal. Hold the iron over an old

the sole plate.                           event of an interruption, the steam inside the      cloth and press the steam trigger. The cloth

                                                 hose would have cooled down and                      absorb the water droplets. After a few

                                                 condensed into water, causing water droplets     seconds, steam instead of water comes

                                                 to escape from the sole plate.                              out of the soleplate.

Wet spots appear on the          The wet spots that appear on your garment        Iron the wet spots without steam for some

garment during ironing.            after you have steam ironed for some time         time to dry them. If the underside of the

                                                 may be caused by steam that has condensed    ironing board is wet, wipe it dry with a piece

                                                 onto the ironing board.                                         of dry cloth.

Flakes and impurities come      Impurities or chemicals present in the water        Clean the soleplate with a damp cloth.

out of the sole plate or the       may have deposited in the steam vents               

the sole plate is dirty.                and/or on the soleplate.

                                                 Too much scale and minerals have                      Descale the appliance regularly (see chapter

                                                 accumulated inside the appliance.                       on “cleaning and maintenance”, section  –

                                                                                                                               descaling the appliance with the 

                                                                                                                               CALC-Clean knob)

Water leaks from the                If you tilt the appliance during while moving        Do not tilt the appliance when the water tank

appliance.                                 it or place it on an uneven surface with the         is full.

                                                 water tank full, water may spill out of the             

                                                 water tank.

MSG-27MAXIcare(IM)241017.qxp_Layout 1  12/5/17  4:20 PM  Page 6

Содержание MSG-27MAXIcare







Отзывы: