background image

3

PARTS REQUIRED

Part Number 82208859

5 AMP 1X                      15 AMP 4X

WARNING: /  AVERTISSEMENT

This vehicle is equipped with a remote controlled engine starter. 
To reduce the risk of serious Injury or death, switch engine starter
system into service mode and disconnect the vehicle battery
before performing any service on the vehicle.
Ce véhicule est doté d'un démarreur à distance.  Pour réduire les 
risques de blessures graves ou mortelles, mettre le démarreur à 
distance en mode service et débrancher la batterie du véhicule 
avant d'effectuer des travaux d'entretien sur celui-ci.

Owner's Manual

Vehicle Remote Start System

TM

Featuring PowerCode Technology

For the Ultimate in Comfort, Convenience and Security

TM

®

1024256 12/03

Remote Control
Car Starter System

Remote Start

Activation

2X

Remote Start

Shutdown

2 sec.

2X                  4X               10X

2X

TOOLS REQUIRED

10mm       1/4”

RT

V SEALENT

VEHICLE PREPARATION

1.

Lower one or more of the passenger windows so the keys do not get locked
in the vehicle.

2.   Disconnect and isolate the negative battery cable.  The battery will need to be

re-connected before programming.

3.  Vehicle requires 2 valid Sentry Keys (if equipped) present at the time of

installation.

2X (French &English)

T-20

Part Number 82209870

Содержание 82209870AG





















Отзывы: