Montigo PVHIN47-200 Скачать руководство пользователя

Страница: 13 / 18

Installation

XG0521 - 180904

Figure 7.

Installing a MTO4F-PV termination.

Figure 7.b

Installing a MTO termination with the MSR frame.

Figure 7.c

Installing a MTO termination with the BSR frame.

12”

2”

12”

Installation of termination with built in frame

A termination with a built-in frame is installed during framing of a

structure.

1. Frame the termination opening to 11" x 11".

2. Install exterior sheathing to the structure framing.
3. Fasten the termination to the sheathing using a minimum of 4 screws.

MSR Frame

MTO4-PV (4"/7")

Termination

MTO4F-PV (4"/7")

Termination

Installation of termination frame at time of framing

Terminations with a MSR frame allow the installation of the frame prior

to installation of the termination.

1. Frame the termination opening to 12" x 12".

2. Secure the MSR Frame to the exterior sheathing of the structure.
3. Fasten the termination to the MSR Frame using a minimum of 4 screws.

Installation of termination frame at time of framing in masonry

Terminations with a BSR frame allow the installation of the frame in

masonry prior to the installation of the termination

1. Frame the BSR opening to 12" x 12".

2. Secure the BSR Frame to the exterior sheathing of the structure.
3. Fasten the termination to the BSR Frame using a minimum of 4 screws.

BSR Frame

11”

Framing

Exterior

Sheathing

Fastening Hard-

ware, minimum

4-screws

Framing

Exterior

Sheathing

Fastening Hardware,

minimum 4-screws

MTO4-PV (4"/7")

Termination

Framing

Exterior

Sheathing

Fastening Hardware,

minimum 4-screws

MT04-PV / MT04F-PV Termination

Содержание PVHIN47-200



















Результаты поиска

Содержание PVHIN47-200

Отзывы:

Похожие инструкции для PVHIN47-200

Бренды по названию

Популярные бренды

Montigo PVHIN47-200, Инструкция по установке и обслуживанию

Результаты поиска

Содержание PVHIN47-200

Отзывы:

Похожие инструкции для PVHIN47-200

Бренды по названию

Популярные бренды